印度BIS认证返回 Back
印度BIS认证
BIS认证是ISI认证发证机构印度标准局（The Bureau of Indian Standards），简称BIS，具体负责产品认证工作。
按《1986 年印度标准局法》（The BIS Act, 1986），印度标准局（BIS）具体负责产品认证工作，它也是印度唯一的产品认证机构。BIS下设5个地区局和19个分局。正式成立于1987年，以取代1946年成立的印度标准学会。
地区局监管对应分局。BIS所属的8个实验室和一些独立实验室负责产品认证过程抽取样品的检验。这些实验室均按ISO/IEC17025：1999执行。
以下产品属于强制性产品类别
| No. | Following products are covered under Compulsory |
| 1 | Cement (any variety of cement manufactured or sold in India) such |
| 2 | Household Electrical goods |
| 3 | Batteries |
| 4 | Oil Pressure Stoves |
| 5 | Automobile Accessories |
| 6 | Cylinder, Valves and Regulator |
| 7 | Medical Equipment |
| 8 | Steel and Iron Products |
| 9 | Electrical Transformers |
| 10 | Electrical Motors |
| 11 | Capacitors |
| 12 | Chemicals, Fertilizers, Polymers & Textiles |
| 13 | Kitchen Appliances |
| 14 | Domestic Water Heaters for use with LPG |
| 15 | Air Conditioner and its related Parts, Hermetic Compressor and Temperature Sensing Controls |
| 16 | Plugs and Socket-Outlets and Alternating Current Direct Connected Static Prepayment Meters for Active Energy |
| 17 | Domestic Gas Stoves for use with Liquefied Petroleum Gases |
| 18 | Transparent Float Glass |
| 19 | Domestic Pressure Cooker |
| 20 | Rubber Hose for Liquefied Petroleum Gas (LPG) |
| 21 | Aluminium Foil |
| 22 | Non Electric Toys |
| 23 | Electric Toys |
| 24 | Flat Transparent Sheet Glass |
| 25 | Safety Glass |
| 26 | Woven Sacks |
| 27 | Butterfly Valves |
| 28 | Reflectors for Bicycles |
| 29 | Paper |
| 30 | Cattle Feeds |
| 31 | Automobile Wheel Rim Component |
| 32 | Foot Wear |
| 33 | Press Tool-Punches |
| 34 | Helmet for riders of Two Wheeler Motor Vehicles |
| 35 | Refrigerating Appliances |
| 36 | Centrifugally cast (Spun) iron pipes |
| 37 | Flux Cored (Tubular) Electrodes |
| 38 | Sewing Machine |
| 39 | Water Treatment System |
| 40 | Jute Bag |
| 41 | Electric Ceiling Type Fans |
| 42 | Wood Based Boards |
| 43 | Cast Iron Products |
| 44 | Solar DC Cable and Fire Survival Cable |
| 45 | Metals and Alloys |
| 46 | Plywood and Wooden flush door shutters |
| 47 | Flux Cored Solder Wire |
| 48 | Miscellaneous Steel Products |
| 49 | Aluminium and Aluminium Alloy Products |
| 50 | Self- Contained Drinking Water Coolers |
| 51 | Medical Textiles |
| 52 | Agro Textiles |
| 53 | Copper Products |
| 54 | Drums and Tins |
| 55 | Door Fittings |
| 56 | Bottled Water Dispenser |
| 57 | Helmet for Police Force, Civil Defence and Personal Protection |
印度标准局（BIS）隶属于消费者事务及公共分配部，它虽为社会法人团体，却行使政府职能，其主要任务是制定推行国家标准；实施合格评定制度；代表国家参与ISO，IEC等国际标准化活动。
自BIS的前身印度标准协会于1955年开始进行产品认证以来，迄今印度产品认证已有50年历史。目前，BIS已颁发产品认证证书3万多份，涵盖农产品、纺织品、电子等几乎每一个工业领域。
BIS证书
·证书持有人为工厂；
·初次申请证书有效期为1年；到期后可选择更新1年期或2年期；
·每年需进行年审；
·每年年审需根据生产带有ISI标识的产品产量计算标识费并交纳相应的费用；
·需在证书到期前3个月内提出证书延期申请
认证模式
样品测试+注册发证
BIS产品认证通过对工厂质量管理体系的初次检验和评定，样品检测，确认合格后发证，认证后由工厂质量管理体系监督。
通过对工厂和市场上抽取样品进行检测，来确定产品是否与印度标准保持一致。
认证周期: 30个工作日（包括测试和注册取证，测试合格和资料齐全）
样品数量:2 – 6 pcs
注册有效期: 2年，到期后直接通过BIS更新
认证流程
1.申请。欲获得BIS认证的国外生产商一般需使用专用的申请书，并准备相关文件向BIS新德里总部申请。
2.记录。BIS对查申请者提交的申请文件和资料进行审查，如手续完备，将申请记录在案。申请者须交纳相应的处理费。
3.初次工厂检验。BIS将指派不超过2人的官员团赴工厂检验。申请者须承担官员团赴工厂检验的差旅、签证费用等开支及相应的检验费用。
4.颁发证书。如果初次检验和测试结果合格，且申请者同意认证后执行BIS认可的检验测试方案并支付BIS标识费，可向申请者颁发证书。证书有效期为1年。证书授予后，执证者每年要支付标识费以及证书年费。
5.认证后监督。BIS通过对执证人的常规监督和对工厂、市场上的样品进行突击检查和测试，监督其认证产品的质量。如果定期检查，从工厂或市场抽取的试样经该工厂检验和独立检测结果满足要求，证书可予以更新。执证者通过提交指定表格向BIS提出更新申请，证书更新费为xxx卢比。执证者还需承担样品检验费用。
测试需要资料：
1.贴有标签的样品
2.贴有标签的适配器和电池（如有）
3.电路原理图
4.电路方块图
5.PCB电路板
6.英文说明书（产品使用环境，安装方法，使用方法，注意事项……）
7.系列产品差异说明
8.关键零部件清单及其认证证书（外壳材料，电源，PCB，电池，变压器…… ，认可零部件可以是有ISI标签/UL认证/CB报告）
9.产品CB报告（如有，请提供）
10.适配器和电池CB报告（如有，请提供）
注册需要资料：
1.Product Information Form
2.Form VI Application Form
3.Form VII Self Evaluation
4.Nomination of Authorized Indian Rep
5.Machinery letter general
6.Business License of factory
7.Authorization letter
8.Letter of Authorization-trakemark-logo
9.Handbook
10.Organizational Structue Diagram
11.Test report
印度ISI认证
印度出口检测认证 印度为统一产品监管标准和要求，确保产品质量和安全，于1955年开始推行产品认证制度。凡列入强制认证的产品，都需按印度产品标准获得产品认证证书才能进入市场。
样本证书：
样本证书：
| Sr No. | IS No. | Product |
| Cement (any variety of cement manufactured or sold in India) | ||
| 1 | IS 12330 | Sulphate Resisting Portland Cement |
| 2 | IS 12600 | Low heat Portland Cement |
| 3 | IS 1489 (Part 1) | Portland Pozzolana Cement-Part1 Fly-ash based |
| 4 | IS 1489 (Part 2) | Portland Pozzolana Cement-Part 2 Calcined clay based |
| 5 | IS 269 | Ordinary Portland Cement |
| 6 | IS 3466 | Masonry Cement |
| 7 | IS 455 | Portland Slag Cement |
| 8 | IS 6452 | High Alumina Cement for Structural use |
| 9 | IS 6909 | Super sulphated cement |
| 10 | IS 8041 | Rapid hardening Portland cement |
| 11 | IS 8042 | White Portland Cement |
| 12 | IS 8043 | Hydrophobic Portland Cement |
| 13 | IS 8229 | Oil well Cement |
| 14 | IS 16415: 2015 | Composite Cement- Specification. |
| 15 | IS 16993: 2018 | Microfine Ordinary Portland Cement- Specification. |
| 16 | IS 15895: 2018 | High Alumina Refractory Cement. |
| Household Electrical goods | ||
| 17 | IS 12640 (Part 1) | Residual current operated circuit breakers for house hold and |
| 18 | IS 12640 (Part 2) |
Residual current operated circuit breakers for household and similar uses–Part 2 Circuit breakers with integral overcurrent protection(RCVOs) |
| 19 | IS 13010 | AC watt-hour meters, class 0.5, 1 & 2 |
| 20 | IS 13779 | AC static watt-hour meters, class 1 & 2 |
| 21 | IS 14697 | AC static transformer operated watt-hour and VAR-hour meters, |
| 22 | IS 15111 (Part 1 & 2) |
Self Ballasted Lamps for General Lighting Services – Part 1 : Safety Requirements & Part 2 : Performance Requirements |
| 23 | IS 302 (Part 2/Sec 3) | Safety of household and similar electrical appliances – Electric iron |
| 24 | IS 302 (Part 2/Sec 201) | Safety of household and similar electrical appliances– Electric immersion water-heaters |
| 25 | IS 302 (Part 2/Sec 202) | Safety of household and similar electrical appliances –Electric stoves |
| 26 | IS 302 (Part 2/Sec 30) | Safety of household and similar electrical appliances-Room heaters |
| 27 | IS 3854 | Switches for domestic and similar purposes |
| 28 | IS 418 | Tungsten filament general service electric lamps (upto100 W ) |
| 29 | IS 694 | PVC insulated cables for working voltages up to and including 1100V |
| 30 | IS 8828 * | Electrical Accessories-Circuit breakers for overcurrent protection for household and similar installations |
| 31 | IS 9968 (Part 1) | Elastomer insulated cables (Part.1): For working voltages up to and including1100 V |
| * Since revised as IS/IEC 60898 | ||
| Batteries | ||
| 32 | IS 8144 | Multi-Purpose dry batteries |
| Food & Related Products | ||
| 33 | IS 15757 | Follow–up formula –complimentary foods |
| 34 | IS 11536 | Processed cereal based complementary foods |
| 35 | IS 1165 | Milk-powder |
| 36 | IS 1166 | Condensed milk, partly skimmed and skimmed condensed milk |
| 37 | IS 12176 | Sweetened ultra high temperature treated condensed milk |
| 38 | IS 13334 (Part 1) | Skimmed milk-powder, standard grade |
| 39 | IS 13334 (Part 2) | Skimmed milk-powder, extra grade |
| 40 | IS 13428 | Packaged Natural Mineral Water |
| 41 | IS 14433 | Infant milk substitutes |
| 42 | IS 17945: 2022 | Food for Special Medical Purpose intended for Infants |
| 43 | IS 14542 | Partly skimmed milk powder |
| 44 | IS 14543 | Packaged Drinking Water (Other than Packaged Natural Mineral Water) |
| 45 | IS 1656 | Milk- cereal Based Complementary foods |
| 46 | IS 14625 | Plastic Feeding Bottles |
| 47 | IS 5168 | Glass Feeding Bottles |
| Oil Pressure Stoves | ||
| 48 | IS 10109 | Oil pressure stove, offset burner type |
| 49 | IS 2787 | Multi-burner oil pressure stoves |
| 50 | IS 1342 | Oil pressure stoves |
| Automobile Accessories | ||
| 51 | IS 13098 | Automotive vehicles –Tubes for pneumatic tyres |
| 52 | IS 15627 | Automotive vehicles– Pneumatic tyres for two and three-wheeled motor vehicles |
| 53 | IS 15633 | Automotive vehicles-Pneumatic tyres for passenger car vehicles– Diagonal and radial ply |
| 54 | IS 15636 | Automotive vehicles- Pneumatic tyres for commercial vehicles-Diagonal and radial ply |
| Cylinder, Valves and Regulator | ||
| 55 | IS 14899 | Liquefied petroleum gas containers for automotive use |
| 56 | IS 15100 | Multifunction valve assembly for permanently fixed liquefied petroleum gas (LPG) containers for automotive use |
| 57 | IS 3196 (Part 4) | Welded low carbon steel cylinders exceeding 5 litre Water capacity for low pressure liquefiable gases Part 4 Cylinders for toxic and corrosive gases |
| 58 | IS 3196 (Part 1) | Welded low carbon steel gas cylinder exceeding 5 litre water capacity for low pressure liquefiable gases Part1 Cylinders for liquefied petroleum gas (LPG) |
| 59 | IS 3196 (Part 2) | Welded low carbon steel gas cylinder exceeding 5-litre water capacity for low pressure liquefiable gases Part 2 Cylinders for liquefiable gases other than LPG. |
| 60 | IS 3224 | Valve fittings for compressed gas cylinder excluding liquefied petroleum gas cylinders |
| 61 | IS 3745 | Yoke Type Valve Connection for Small Medical Gas Cylinders |
| 62 | IS 7142 | Welded low carbon steel cylinders for low pressure liquefiable gases not exceeding 5 litre water capacity |
| 63 | IS 7285 (Part 1) | Refillable Seamless steel gas cylinders Part1 Normalized steel cylinders |
| 64 | IS 7285 (Part 2) | Refillable Seamless steel gas cylinders Part 2 Quenched and tempered steel cylinders with tensile strength less than 1100 MPa (112 kgf/mm2) |
| 65 | IS 7302 | Valve fittings for gas cylinder valves for use with breathing apparatus |
| 66 | IS 7312 | Welded and seamless steel dissolved acetylene gas cylinders |
| 67 | IS 8737 | Valve fittings for use with liquefied petroleum gas cylinders of more than 5 litre water capacity Part 2 Valve fittings for newly manufactured LPG cylinders |
| 68 | IS 8776 | Valve Fittings for Use with Liquefied Petroleum Gas (LPG) Cylinders up to and Including 5-Litre Water Capacity |
| 69 | IS 9798 | Low pressure regulators for use with liquefied petroleum gas (LPG) mixtures |
| Medical Equipment | ||
| 70 | IS 3055 (Part 1) | Clinical thermometers :Part1 Solid stem type |
| 71 | IS 3055 (Part 2) | Clinical thermometers :Part 2 Enclosed scale type |
| 72 | IS 7620 (Part 1) | Diagnostic Medical X-Ray Equipment |
| Steel and Iron Products | ||
| 73 | IS 1785 (Part 1) : 1983 | Plain Hard-drawn Steel Wire For Pre-stressed Concrete: Part 1 Cold Drawn Stress-relieved Wire |
| 74 | IS 1785 (Part 2) : 1983 | Plain hard-drawn steel wire for pre-stressed concrete Part 2: As drawn wire |
| 75 | IS 6003:2010 | Indented wire for Pre-stressed concrete |
| 76 | IS 6006:2014 | Uncoated stress relieved strand for Pre-stressed concrete. |
| 77 | IS 13620:1993 | Fusion bonded epoxy coated reinforcing bars |
| 78 | IS 14268:1995 | Uncoated Stress Relieved Low Relaxation Seven-ply Strand For Pre-stressed Concrete. |
| 79 | IS 277:2003 | Galvanized steel sheets ( plain and corrugated). |
| 80 | IS 2002:2009 | Steel plates for pressure vessels for intermediate and high temperature service including boilers. |
| 81 | IS 2041:2009 | Steel plates for pressure vessels used at moderate and low temperature |
| 82 | IS 2830:2012 | Carbon steel cast billet ingots ,billets, blooms and slabs for rerolling into steel for general structural purpose |
| 83 | IS 1786:2008 | High strength deformed steel bars and wires for concrete reinforcement |
| 84 | IS 648:2006 | Cold rolled non-oriented electrical steel sheets and strip-fully processed type (CRNO) |
| 85 | IS 3024:2015 | Grain oriented electrical steel sheet & strip (CRGO) |
| 86 | IS 15391:2003 | Oriented Electrical Steel Sheet and Strip- Semi-Processed Type- Specification. |
| 87 | IS 2062:2011 | Hot rolled medium and high tensile structural steel |
| 88 | IS 432 : Part 1:1982 | Mild Steel and Medium Tensile Steel Bars and Hard–Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild steel and medium tensile steel bars |
| 89 | IS 432 : Part 2:1982 | Mild steel and Medium Tensile steel bars and Hard–Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard- Drawn Steel Wire |
| 90 | IS 513 (Part-1): 2016 | Cold reduced carbon steel sheets and strips Part 1 Cold Forming and Drawing Purpose |
| 91 | IS 513(Part-2):2016 | Cold reduced carbon steel sheets and strips Part 2 High Tensile and Multi-phase Steel |
| 92 | IS 1079: 2017 | Hot Rolled Carbon Steel Sheet, Plate and Strip — Specification. |
| 93 | IS 1875:1992 | Carbon steel billets, blooms, slabs and bars for forgings. |
| 94 | IS 2879:1998 | Mild steel for metal arc welding electrodes. |
| 95 | IS 3502:2009 | Steel Chequered Plates |
| 96 | IS 5872:1990 | Cold Rolled Steel Strips (Box Strappings). |
| 97 | IS 5986: 2017 | Hot Rolled Steel Sheet, Plate and Strip for Forming and Flanging Purposes — Specification. |
| 98 | IS 6240:2008 | Hot Rolled Steel Plate (up to 6 mm) Sheet and Strip for the Manufacture of Low Pressure Liquefiable Gas Cylinders |
| 99 | IS 7283:1992 | Hot Rolled bars for production of bright bars and machined parts for engineering applications. |
| 100 | IS 7887:1992 | Mild steel wire rods for general engineering purposes. |
| 101 | IS 10748:2004 | Hot Rolled Steel Strip for Welded Tubes and Pipes. |
| 102 | IS 11513:2017 | Hot Rolled Carbon Steel Strip for Cold Rolling Purposes — Specification |
| 103 | IS 15647:2006 | Hot rolled steel narrow width strip for welded tubes and pipes |
| 104 | IS 7904:2017 | High carbon steel wire rods- Specification |
| 105 | IS 14246:2013 | Continuously pre-painted galvanized steel sheets and coils |
| 106 | IS 15965:2012 | Pre-painted aluminium zinc alloy metallic coated steel strip and sheet (Plain). |
| 107 | IS 280: 2006 | Mild steel wire for General Engineering purposes. |
| 108 | IS 1835:1976 | Round Steel wire for ropes |
| 109 | IS 3975:1999 | Low Carbon Galvanized steel wires formed wires and Tapes for armouring of Cables |
| 110 | IS 4368:1967 | Alloy Steel billets, blooms and slabs for forging for general engineering purposes. |
| 111 | IS 4454 (Part 1) : 2001 | Steel wire for mechanical springs Part-1 cold drawn unalloyed steel wire. |
| 112 | IS 4454 (Part 2): 2001 | Steel wire for mechanical springs Part-2 oil hardened and tempered steel wire. |
| 113 | IS 4824:2006 | Bead Wires for Tyres |
| 114 | IS 11169 (Part 1): 1984 | Steels for Cold Heading/Cold extrusion application Part-1 Wrought carbon and low alloy steels |
| 115 | IS 11587:1986 | Structural Weather resistant steel. |
| 116 | IS 15103: 2002 | Fire resistant Steel- Specification |
| 117 | IS 15914:2011 | High Tensile Strength Flat Rolled Steel Plate (Up to 6 mm), Sheet and Strip for the Manufacture of Welded Gas Cylinder. |
| 118 | IS 15961:2012 | Hot Dip aluminium- Zinc alloy metallic coated steel strip and sheet (Plain) |
| 119 | IS 15962:2012 | Structural Steel for Building for Structures with improved seismic Resistance |
| 120 | IS 6527:1995 | Stainless Steel wire Rod |
| 121 | IS 6528:1995 | Stainless Steel Wires |
| 122 | IS 6603:2001 | Stainless Steel Bars and Flats |
| 123 | IS 5522:2014 | Stainless Steel sheets and strips for utensils- Specification |
| 124 | IS 6911:2017 | Stainless Steel Plate, Sheet and Strip- Specification |
| 125 | IS 15997:2012 | Low Nickel Austenitic Stainless Steel Sheet and Strip For Utensils and Kitchen Applications- Specification |
| 126 | IS 1110 : 1990 | Ferrosilicon – Specification |
| 127 | IS 4409 : 1973 | Specification for Ferronickel |
| 128 | IS 1029 : 1970 | Specification for Hot rolled steel strip (bailing) |
| 129 | IS 2385 : 1977 | Specification for Hot-rolled mild steel sheet and strip in coil form for cold-reduced tinplate and cold-reduced black plate |
| 130 | IS 3039 : 1988 | Specification for Structural steel for construction of hulls of ships |
| 131 | IS 9550 2001 | Bright steel bars – v Specification |
| 132 | IS 3748 : 1990 | Tool and die steels – Specification |
| 133 | IS 5517 : 1993 | Steel for hardening and tempering – Specification |
| 134 | IS 7291 : 1981 | Specification for High speed tool steels |
| 135 | IS 7494 : 1981 | Specification for Steel for valves for internal combustion engines |
| 136 | IS 12146 : 1987 | Specification for Carbon manganese steel forgings for pressure vessels |
| 137 | IS 16585 : 2016 | Magnetic materials – specification for individual material – Fe based amorphous strip delivered in the semi-processed state. |
| 138 | IS 2831 : 2012 | Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (ordinary quality) – Specification |
| 139 | IS 1148: 2009 | Steel Rivet Bars (medium And High Tensile) – For Structural Purposes |
| 140 | IS 1673: 1984 | Specification for Mild Steel Wire, Cold Heading Quality |
| 141 | IS 1812: 1982 | Specification for Carbon Steel Wire for the Manufacture of Wood Screws |
| 142 | IS 2507: 1975 | Specification for Cold – rolled Steel Strips For Springs. |
| 143 | IS 2255: 1977 | Specification for Mild Steel Wire Rod for the Manufacture of Machine Screws (By Cold Heading Process). |
| 144 | IS 3195: 1992 | Steel For the Manufacture of Volute And Helical Springs (for Railway Rolling Stock) – Specification . |
| 145 | IS 3431: 1982 | Specification for Steel for the manufacture of volute, helical and laminated springs for automotive suspension. |
| 146 | IS 3885-Part-1: 1992 | Steel for the manufacture of laminated springs (railway rolling stock) Part 1 Flat Sections – Specification. |
| 147 | IS 3885-Part- 2: 1992 | Steel for the manufacture of laminated springs (railway rolling stock) Part 2: Rib and Groove Sections- Specification. |
| 148 | IS 4223: 1975 | Specification for Steel Wire for Umbrella Ribs . |
| 149 | IS 4224: 1972 | Specification for Steel Wire for Staples, Pins And Clips. |
| 150 | IS 4397: 1999 | Cold-rolled Carbon Steel Strips for Ball and Roller Bearing Cages/ Retainers- Specification. |
| 151 | IS 4398: 1994 | Carbon-chromium Steel for the Manufacture of Balls, Rollers and Bearing Races- Specification |
| 152 | IS 6902: 1973 | Specification for Steel Wire for spokes. |
| 153 | IS 6967: 1973 | Specification for Steel For Electrically welded round Link Chains. |
| 154 | IS 7226: 1974 | Specification for Cold rolled medium, high carbon and low alloy steel strip for general engineering purposes. |
| 155 | IS 7557: 1982 | Specification for Steel Wire: (Up to 20 mm) for the manufacture of cold-forged rivets. |
| 156 | IS 8052: 2006 | Steel ingots, billets and blooms for the production of springs, rivets and screws for general engineering applications – Specification. |
| 157 | IS 8951: 2001 | Steel Cast Billet Ingots, Billets and Blooms for production of High Carbon Steel Wire Rods- Specification |
| 158 | IS 8952: 1995 | Steel ingots, blooms and billets for production of mild steel wire rods for general engineering purposes – Specification |
| 159 | IS 9476: 1980 | Specification for Cold rolled steel strips for carbon steel razor blades. |
| 160 | IS 9962: 1981 | Specification for Steel Wire for Needles. |
| 161 | IS 12367:1988 | Specification for Cold-rolled Carbon Steel Strips/ Coils for Manufacture of Welded Tubes. |
| 162 | IS 14331:1995 | Steels for High Temperature Bolting Applications – Specification |
| 163 | IS 14491:1997 | Low carbon high strength cold rolled steel sheets and coils for cold forming- Specification |
| 164 | IS 14650:1999 | Carbon Steel Cast Billet Ingots, Billets, Blooms and Slabs for Rerolling purposes- Specification |
| 165 | IS 4882: 1979 | Specification for Low Carbon Steel Wire for Rivets for use in Bearing Industry |
| 166 | IS 2090:1983 | Specification for High Tensile Steel Bars used in Pre-stressed Concrete |
| 167 | IS 6529:1996 | Stainless Steel Blooms Billets And Slabs For Forging |
| 168 | IS 9294:1979 | Cold-Rolled Stainless Steel Strips for Razor Blades |
| 169 | IS 10631:1983 | Stainless Steel for welding electrode core wire |
| 170 | IS 10632 (Part 2):1983 | Specification for Non Magnetic stainless steel for electrical applications Part 2 Specific requirements for binding wire. |
| 171 | IS 10632 (Part 3):1983 | Specification for Non Magnetic stainless steel for electrical applications Part 3 Specific requirements for sheets, strips and plates. |
| 172 | IS 11169 (Part 2): 1989 | Steels for cold heading/cold extrusion applications – specification Part 2 Stainless steel |
| 173 | IS 5651:1987 | Steels for Pneumatic Tools |
| 174 | IS 9516:1980 | Heat Resisting Steels |
| 175 | IS 11952:1986 | Steels For Piston Pins (Gudgeon Pins) |
| 176 | IS 12045:1987 | Alloys Used in Electrical Resistance Metallic Heating Elements |
| 177 | IS 14652:1999 | 18 Percent Nickel Maraging Steel Bars and Rods |
| 178 | IS 1566:1982 | Specification for Hard-drawn Steel Wire Fabric For Concrete Reinforcement |
| 179 | IS 5489: 1975 | Carburizing Steels For Use in Bearing Industry. |
| 180 | IS 11946:1987 | Soft Magnetic Iron Strips |
| 181 | IS 11947:1987 | Soft Magnetic Iron Rods, Bars Flats and Sections |
| 182 | IS 963: 1958 | Chrome molybdenum steel bars and rods for aircraft purposes |
| 183 | IS 4454 (Part 4): 2001 | Steel Wires for Mechanical Springs- Part 4: Stainless Steel Wire |
| 184 | IS 1993 : 2018 | Cold-reduced Electrolytic Tin Plate |
| 185 | IS 12591:2018 | Cold-reduced Electrolytic Chromium/Chromium oxide – coated steel |
| 186 | IS 412:1975 | Expanded Metal Steel Sheets For General Purposes |
| 187 | IS 2100: 1970 | Steel Billets,Bars And Sections For Boilers |
| 188 | IS 2589: 1975 | Hard Drawn Steel Wire For Upholstery Springs |
| 189 | IS 3298: 1981 | Mild Steel Rivet Bars For Ship Building |
| 190 | IS 4072: 1975 | Steel For Spring Washers |
| 191 | IS 8510 (Part II): 1977 | Steel Wire For Banding Of Armatures And Rotors Part II Specific Requirements for magnetic banding wires |
| 192 | IS 8510 (PartIII): 1977 | Tinned Steel Wire For Banding Of Armatures And Rotors Part III Specific Requirements for non-magnetic banding wires |
| 193 | IS 8563: 1977 | Half Round Mild Steel Wire For The Manufacture of Split Pins |
| 194 | IS 8564: 1977 | Steel Wire For Nipples For Spokes |
| 195 | IS 8565: 1977 | Heald Wire |
| 196 | IS 8566: 1977 | Steel Wire For Reeds |
| 197 | IS 8917: 1978 | Plates For Galvanizing Pots |
| 198 | IS 9442: 1980 | Hot Rolled Steel Plates Sheets And Strips For Manufacture of Agricultural Discs |
| 199 | IS 9485: 1980 | Cold-Reduced And Hot-Rolled Carbon Steel Sheet For Porcelain Enamelling |
| 200 | IS 10794: 1984 | Mild steel wire for cotter pins |
| 201 | IS 12262:1988 | Trapezoidal Steel Wire For Springs Washers |
| 202 | IS 12313: 1988 | Hot-Dip Terne Coated Carbon Steel Sheets |
| 203 | IS 15911:2010 | Structural Steel (Ordinary Quality) |
| 204 | IS 4430: 1979 | Mould Steels |
| 205 | IS 4431: 1978 | Carbon And Carbon- Manganese Free- Cutting Steels |
| 206 | IS 4432: 1988 | Case Hardening Steels |
| 207 | IS 5518: 1996 | Steels For Die Blocks For Drop Forging |
| 208 | IS 8748: 1978 | Forged/Rolled CTC Segments |
| 209 | IS 12145: 1987 | Quenched And Tempered Alloy Steel Forgings For Pressure Vessels |
| 210 | IS 13387: 1992 | Tool Steel Forgings For Metal Forming |
| 211 | IS 14698:1999 | Carbon And Low Alloy Billets, Blooms, Slabs And Bars For Manufacture Of Shell BodiesAnd Proof Shots Used In Defence Services |
| 212 | IS/ISO 11951 : 2016 | Cold – Reduced tinmill products – Blackplate |
| 213 | IS 3930: 1994 | Flame And Induction Hardening Steels |
| 214 | IS 5478: 1969 | Thermostat Metal Sheet and Strip |
| 215 | IS 13352: 1992 | Stock for Forgings produced from Continuously Cast Blooms, Billets and Slabs |
| 216 | IS 16644: 2018 | Stress-Relieved, Low Relaxation Steel Wire for Pre-stressed Concrete |
| 217 | IS 17404 : 2020 | Electrogalvanized Hot Rolled and Cold Reduced Carbon Steel Sheetsand Strips |
| 218 | IS 8329 : 2000 | Centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage |
| 219 | IS 9523:2000 | Ductile iron fittings for pressure pipes for water, gas and sewage |
| 220 | IS 1161:2014 | Steel tubes for structural purposes |
| 221 | IS 1239 (Part 1):2014 | Steel Tubes, Tubulars and Other Wrought Steel Fittings – Part 1 : Steel Tubes |
| 222 | IS 4270:2001 | Steel tubes used for water-wells (upto 200 mm dia) |
| 223 | IS 9139:1979 | Specification for Malleable iron shots and grits for use in foundries |
| Electrical Transformers | ||
| 224 | IS 1180 (Part 1) | Out door type Oil immersed Distribution Transformers upto and including 2500 kVA, 33 KV-specification Part 1 Mineral oil immersed |
| Electrical Motors | ||
| 225 | IS 12615 | Energy Efficient Induction Motors-Three Phase Squirrel Cage |
| Capacitors | ||
| 226 | IS 2993 | A.C. motor capacitors |
| 227 | IS 13340 | Power Capacitors of Self-healing Type for AC Power Systems having Rated Voltage up to 650V |
| 228 | IS 13585 Part 1 | Shunt Power Capacitors of the Non-Self-Healing Type for AC System having a Rated Voltage up to and Including 1000V Part-1 General Performance, Testing amd Rating Safety Requirements Guide for Installation and Operation |
| Chemicals, Fertilizers, Polymers & Textiles | ||
| 229 | IS 252:2013 | Caustic Soda -Specification |
| 230 | IS 10116 : 2015 | Boric Acid – Specification |
| 231 | IS 15573 | Poly Aluminium Chloride |
| 232 | IS 695 | Acetic Acid |
| 233 | IS 2833 | Aniline |
| 234 | IS 517 | Methanol |
| 235 | IS 5158: 1987 | Specification for Phthalic Anhydride, Technical |
| 236 | IS 8058:2018 | Pyridine |
| 237 | IS 16113:2013 | Gamma Picoline |
| 238 | IS 16112:2013 | Beta Picoline |
| 239 | IS 12084: 2018 | Morpholine |
| 240 | IS 297:2001 | Sodium Sulphide, Technical |
| 241 | IS 7129:1992 | Potassium Carbonate, Anhydrous |
| 242 | IS 170:2004 | Acetone |
| 243 | IS 4581:1978 | Phosphorous Trichloride, pure and Analytical Reagent |
| 244 | IS 11744:1986 | Phosphorous Pentachloride, Technical |
| 245 | IS 11657:1986 | Phosphorous Oxychloride, Technical |
| 246 | IS 2080:2021 | Stabilized Hydrogen Peroxide |
| 247 | IS 3205:1984 | Precipitated Barium Carbonate, Technical |
| 248 | IS 12928:1990 | Precipitated Barium for Ceramic and Glass Industry |
| 249 | IS 4505:2015 | Sodium Formaldehyde Sulphoxylate |
| 250 | IS 6100:1984 | Sodium Tripolyphosphate,Anhydrous,Technical |
| 251 | IS 14709:1999 | n- Butyl Acrylate |
| 252 | IS 336:1973 | Ether |
| 253 | IS 5295:1985 | Ethylene Glycol |
| 254 | IS 537:2011 | Toluene |
| 255 | IS 15030:2001 | Terephthalic Acid |
| 256 | IS 14707: 1999 | Methyl Acrylate |
| 257 | IS 14708:1999 | Ethyl Acrylate |
| 258 | IS 12345:1988 | Vinyl Acetate Monomer |
| 259 | IS 4105:2020 | Styrene (Vinyl Benzene) |
| 260 | IS 5149:2020 | Maleic Anhydride, Technical |
| 261 | IS 12540:1988 | Acrylonitrile |
| 262 | IS 17265:2019 | 100 Percent. Polyester Spun Grey and White Yarn (PSY) |
| 263 | IS 17261:2019 | Polyester Continuous Filament Fully Drawn Yarn (FDY) |
| 264 | IS 17264:2019 | Polyester Industrial Yarn (IDY) |
| 265 | IS 17262:2019 | Polyester Partially Oriented Yarn (POY) |
| 266 | IS 17263:2019 | Polyester Staple Fibres (PSF) |
| 267 | IS 7328:2020 | Polyethylene Material for moulding and extrusion |
| 268 | IS 11356:2020 | Styrene-Butadiene Rubber Latex |
| 269 | IS 16481:2016 | Synthetic Micro-Fibres for use in Cement Based Matrix |
| 270 | IS 12795:2020 | Linear Alkyl Benzene |
| 271 | IS 13601:1993 | Ethylene Vinyl Acetate (EVA) Copolymers |
| 272 | IS 7686:2020 | 3(N, N-DiEthyl) Aminophenol |
| 273 | IS 4566:2020 | Methylene Chloride (Dichloromethane) |
| 274 | IS 2012:2006 | Red Phosphorus |
| 275 | IS 17077 :2019/ISO 19062-1 : 2015 | Acrylonitrile Butadiene Styrene (ABS) |
| 276 | IS 869:2020 | Ethylene Dichloride |
| 277 | IS 17370:2020 | p-Xylene |
| 278 | IS 14434:1998 | Polycarbonate |
| 279 | IS 17397 (Part 1) : 2020/ISO 16365-1 : 2014 | Polyurethanes |
| 280 | IS 17442:2020 | Vinyl Chloride Monomer |
| 281 | IS 17450 : 2020 | 1,3 Phenylenediamine |
| 282 | IS 10931 : 1984 | Lauric Acid |
| 283 | IS 12029 : 1986 | Acid Oil |
| 284 | IS 12067: 1987 | Palm Fatty Acids |
| 285 | IS 12068 :1987 | Rice Bran Fatty Acids |
| 286 | IS 12069 : 1987 | Coconut Fatty Acids |
| 287 | IS 12124 : 1987 | Rubberseed Fatty Acids |
| 288 | IS 12361 :1988 | Hydrogenated Rice Bran Fatty Acids |
| Kitchen Appliances | ||
| 289 | IS 302 (Part 2/ Section 14) | Hand-held Blender |
| 290 | IS 4250 | Domestic Electric Food Mixer (Liquidizers and Grinders) and Centrifugal Juicer |
| Domestic Water Heaters for use with LPG | ||
| 291 | IS 15558 | Instantaneous Domestic Water Heater for use with Liquefied Petroleum Gas |
| Air Conditioner and its related Parts, Hermetic Compressor and Temperature Sensing Controls | ||
| 292 | IS 1391 (Part-1): 2017 | Room Air Conditioners- Specification Part 1 Unitary Air Conditioners |
| 293 | IS 1391 (Part-2): 2018 | Room Air Conditioners- Specification Part 2 Split Air Conditioners |
| 294 | IS 8148:2018 | Ducted and Package Air Conditioners |
| 295 | IS 11329:2018 | Finned type Heat Exchanger for Room Air Conditioner |
| 296 | IS 10617:2018 | Hermetic compressor |
| Hermetic Compressors-Specification | ||
| Plugs and Socket-Outlets and Alternating Current Direct Connected Static Prepayment Meters for Active Energy | ||
| 297 | IS 1293 : 2005 | Plugs and socket-outlets of Rated Voltage up to and including 250 Volts and Rated current up to and including 16 amperes |
| 298 | IS 15884:2010 | Alternating Current Direct Connected Static Prepayment Meters for Active Energy (Class1 and 2) |
| Domestic Gas Stoves for use with Liquefied Petroleum Gases | ||
| 299 | IS 4246: 2002 | Domestic Gas Stoves for use with Liquefied Petroleum Gases |
| Transparent Float Glass | ||
| 300 | IS 14900: 2018 | Transparent Float Glass |
| Domestic Pressure Cooker | ||
| 301 | IS 2347:2017 | Domestic Pressure Cooker |
| Cables | ||
| 302 | IS 1554(Part 1) : 1988 | Specification for PVC Insulated (Heavy Duty) Electric Cables Part 1 For Working Voltages up to and Including 1100 V |
| 303 | IS 1554(Part 2) : 1988 | Specification for PVC Insulated (Heavy Duty) Electric Cables Part 2 For Working Voltages from 3.3 kV up to and Including 11 kV |
| 304 | IS 7098 (Part 1) : 1988 | Specification for Crosslinked Polyethylene Insulated PVC Sheathed Cables Part 1 for working voltages up to and including 1100 V |
| 305 | IS 7098 (Part 2) : 2011 | Crosslinked polyethylene insulated Thermoplastics sheathed cables – Specification Part 2 for working voltages from 3.3 kV up to and including 33 kV |
| 306 | IS 7098 (Part 3) : 1993 | Cross-Linked Polyethylene Insulated Thermoplastics Sheathed Cables Part 3 For Working Voltages from 66 kV Up to and Including 220 kV |
| 307 | IS 14255 : 1995 | Aerial Bunched Cables – For Working Voltages Up to and Including 1100 Volts – Specification |
| 308 | IS 9968 (Part 2) : 2002 | Specification for Elastomer Insulated Cables Part 2 For Working Voltages form 3.3 kV Up to and Including 33 kV |
| 309 | IS 8784 : 1987 | Specification for Thermocouple Compensating Cables |
| 310 | IS 9857 : 1990 | Welding Cables – Specification |
| 311 | IS 14494 : 2019 | Elastomer Insulated Flexible Cables for Use in Mines – Specification |
| 312 | IS 2593 : 1984 | Specification for Flexible Cables for Miner’s Cap-Lamps |
| 313 | IS 5950 : 1984 | Specification for Shot Firing Cables (for use other than in shafts) |
| 314 | IS 17048 : 2018 | Halogen Free Flame Retardant (HFFR) Cables for Working Voltages Up to and Including 1100 V – Specification |
| Rubber Hose for Liquefied Petroleum Gas (LPG) | ||
| 315 | IS 9573(Part 1):2017 | Rubber Hose for Liquefied Petroleum Gas (LPG)- Specification Part 1 Industrial Application |
| 316 | IS 9573(Part 2):2017 | Rubber Hose for Liquefied Petroleum Gas (LPG)- Specification Part 2- Domestic and Commercial Application. |
| Aluminium Foil | ||
| 317 | IS 15392 | Aluminium and Aluminium Alloy Bare Foil for Food Packaging |
| Non Electric Toys | ||
| 318 | IS 9873 (Part 1) : 2018 | Safety of Toys Part l Safety Aspects Related to Mechanical and Physical Properties. |
| IS 9873 (Part 2) : 2017 | Safety of Toys Part 2 Flammability. | |
| IS 9873 (Part 3) : 2017 | Safety Requirements for Toys Part 3 Migration of Certain Elements. | |
| IS 9873 (Part 4) : 2017 | Safety of Toys Part 4 Swings, Slides and Similar Activity Toys for Indoor and Outdoor Family Domestic Use. | |
| IS 9873 (Part 7) : 2017 | Safety of Toys Part 7 Requirements and Test Methods for Finger Paints. | |
| IS 9873 (Part 9) : 2017 | Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children’s Products. | |
| Electric Toys | ||
| 319 | IS 15644: 2006 | Safety of Electric Toys. |
| Flat Transparent Sheet Glass | ||
| 320 | IS 2835 : 1987 | Flat Transparent Sheet Glass. |
| Safety Glass | ||
| 321 | IS 2553 (Part 1):2018 | Safety Glass -Specification Part 1 Architectural, Building and General uses. |
| 322 | IS 2553 (Part 2):2019 | Safety Glass -Specification Part 2 For Road Transport . |
| Woven Sacks | ||
| 323 | IS 14887:2014 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for packaging of 50 kilogram Foodgrains |
| 324 | IS 16208:2015 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for packaging 10 kilogram, 15 kilogram, 20 kilogram, 25 kilogram, and 30 kilogram Foodgrains |
| 325 | IS 14968:2015 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for packaging 50 kilogram /25 kilogram Sugar |
| 326 | IS 14252:2015 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for filling Sand |
| Butterfly Valves | ||
| 327 | IS 13095:1991 | Butterfly valves for general purpose |
| Reflectors for Bicycles | ||
| 328 | IS/ISO 6742-2:2015 | Retro-reflective Devices |
| Paper | ||
| 329 | IS 14490:2018 | Plain Copier Paper |
| Cattle Feeds | ||
| 330 | IS 2052 : 2009 | Compounded Feeds for Cattle |
| Automobile Wheel Rim Component | ||
| 331 | IS: 16192 (Part 1) | Automotive Vehicles Wheel Rims for Two and Three Wheeled Vehicles Part 1 |
| 332 | IS: 16192 (Part 2) | Automotive Vehicles Wheel Rims for Two and Three Wheeled Vehicles Part 2 |
| Sheet Metal Wheel Rims Method of Tests and Requirements | ||
| 333 | IS: 16192 (Part 3) | Automotive Vehicles Wheel Rims for Two and Three Wheeled Vehicles Part 3 |
| Spoke Wheel Rims Method of Tests and Requirements | ||
| 334 | IS: 9436 | Performance Requirements and Methods of Tests for Wheels for Passenger Cars |
| 335 | IS: 9438 | Performance Requirements and Methods of Tests for Wheels or Rims for Trucks and Buses |
| Foot Wear | ||
| 336 | IS 5557: 2004 | Industrial and protective rubber knee and ankle boots |
| 337 | IS 5557 (Part 2): 2018 | All rubber gum boots and ankle boots |
| 338 | IS 5676: 1995 | Moulded solid rubber soles and heels |
| 339 | IS 6664: 1992 | Rubber microcellular sheets for soles and heels |
| 340 | IS 6719: 1972 | Solid PVC soles and heels |
| 341 | IS 6721: 1972 | PVC sandal |
| 342 | IS 10702: 1992 | Rubber Hawai Chappal |
| 343 | IS 11544: 1986 | Slipper, rubber |
| 344 | IS 12254: 1993 | Polyvinyl chloride(PVC) industrial boots |
| 345 | IS 13893: 1994 | Polyurethane sole, semirigid |
| 346 | IS 13995: 1995 | Unlined moulded rubber boots |
| 347 | IS 16645: 2018 | Moulded plastics footwear- Lined or Unlined polyurethane boots for general industrial use |
| 348 | IS 16994: 2018 | Footwear for men and women for municipal scavenging work |
| 349 | IS 1989 (Part 1): 1986 | Leather safety boots and shoes for miners |
| 350 | IS 1989 (Part.2): 1986 | Leather safety boots and shoes for heavy metal industries |
| 351 | IS 3735: 1996 | Canvas Shoes Rubber Sole |
| 352 | IS 3736: 1995 | Canvas Boots Rubber Sole |
| 353 | IS 3976: 2018 | Safety Rubber Canvas Boots for Miners |
| 354 | IS 11226: 1993 | Leather safety footwear having direct moulded rubber sole |
| 355 | IS 14544: 1998 | Leather safety footwear with direct moulded polyvinyl chloride (PVC) sole |
| 356 | IS 15844: 2010 | Sports footwear |
| 357 | IS 17012: 2018 | High ankle tactical boots with PU – Rubber sole |
| 358 | IS 17037: 2018 | Antiriot shoes |
| 359 | IS 17043: 2018 | Derby shoes |
| 360 | IS 15298 (Part 2): 2016 | Personal protective equipment – Part 2 Safety Footwear |
| 361 | IS 15298 ( Part 3) : 2019 | Personal protective equipment – Part 3 Protective Footwear |
| 362 | IS 15298 (Part 4) : 2017 | Personal protective equipment – Part 4 Occupational Footwear |
| Press Tool-Punches | ||
| 363 | IS 4296 (Part 1):2016 | Tools for Pressing Part 1 Round Punches with 60 Degrees Conical Head and Straight Shank |
| 364 | IS 4296 (Part 2):2016 | Tools for Pressing Part 2 Punches with Cylindrical Head and Straight or Reduced Shank |
| 365 | IS 4296 (Part 3):2016 | Tools for Pressing Part 3 Round Punches with 60 Degrees Conical Head and Reduced Shank |
| Helmet for riders of Two Wheeler Motor Vehicles | ||
| 366 | IS 4151: 2015 | Helmet for riders of Two Wheeler Motor Vehicles |
| Refrigerating Appliances | ||
| 367 | IS 17550 (Part 1): 2021 | Household Refrigerating Appliances- Characteristics and Test Methods part-1 General Requirements |
| 368 | IS 7872: 2018 | Freezers |
| Centrifugally cast (Spun) iron pipes | ||
| 369 | IS 1536: 2001 | Centrifugally cast (Spun) iron pressure pipes for water, gas and sewage |
| 370 | IS 3989: 2009 | Centrifugally cast (Spun) iron spigot and socket soil, waste, ventilating and rainwater pipes, fittings and accessories |
| 371 | IS 15905: 2011 | Hubless centrifugally cast (Spun) iron pipes, fittings and accessories – Spigot series |
| Flux Cored (Tubular) Electrodes | ||
| 372 | IS 15769:2008 | Flux Cored (Tubular) Electrodes for Gas Shielded and Self-Shielded Metal Welding of Carbon or Carbon- Manganese Steel |
| Sewing Machine | ||
| 373 | IS 15449 : Part 1 : 2004 | Household Zig-Zag Sewing Machine Head |
| Water Treatment System | ||
| 374 | IS 16240 : 2015 | Reverse Osmosis (RO) Based Point-Of-Use (POU) Water Treatment System |
| Jute Bag | ||
| 375 | IS 1943:1995 | A- twill Jute Bag |
| 376 | IS 2566:1993 | B-twill Jute bags for packing foodgrains |
| 377 | IS 12650:2018 | Jute bags for packing 50 Kg foodgrains |
| 378 | IS 15138:2010 | Jute bags for packing 50 Kg sugar |
| 379 | IS 16186:2014 | Light weight jute sacking bags for packing 50 Kg foodgrains |
| 380 | IS 16372:2015 | Jute bags for packing up to 30 Kg foodgrains |
| 381 | IS 17266:2019 | Viscose Staple Fibres |
| 382 | IS 15351 : 2015 | Laminated High Density Polyethylene (HDPE) Woven Geomembrane for Water Proof Lining |
| 383 | IS 15909 : 2020 | Poly Vinyl Chloride (PVC) Geomembranes |
| 384 | IS 16653 : 2017 | Needle punched non-woven geobags |
| 385 | IS 16654: 2017 | Polypropylene Multifilament woven geobags |
| 386 | IS 14715 (Part 1): 2016 | Jute Geotextiles |
| 387 | IS 14715 (Part 2): 2016 | Jute Geotextiles |
| 388 | IS 15869 : 2020 | Open Weave Coir Bhoovastra |
| 389 | IS 16391 : 2015 | Geotextiles used in sub-grade separation in pavement structures |
| 390 | IS 16393 : 2015 | Geotextiles used in Subsurface Drainage Application |
| 391 | IS 16362 : 2020 | Geotextiles used in Sub-grade Stabilisation in pavement structures |
| 392 | IS 16352 : 2020 | High Density Polyethylene (HDPE) Geomembranes for lining |
| 393 | IS 16090:2013 | Geotextiles used as protection (or cushioning) materials |
| 394 | IS 16392:2015 | Geotextiles for permanent erosion control in hard armor systems |
| 395 | IS 17371:2020 | Geogrids for flexible pavements |
| 396 | IS 17372:2020 | Polymeric strip or geostrip used as soil reinforcement in retaining structures |
| 397 | IS 17373:2020 | Geogrids used in reinforced soil retaining structures |
| 398 | IS 17374:2020 | Reinforced HDPE membrane for effluents and chemical resistance lining |
| 399 | IS 17483 (Part 1): 2020 | Geocells |
| 400 | IS 17483 (Part 2): 2020 | Geocells |
| 401 | IS 15741 : 2007 | Curtains and Drapes |
| 402 | IS 15768 : 2008 | Upholstered composites used for non-domestic furniture |
| 403 | IS 16890 : 2018 | Protective clothing for firefighters |
| 404 | IS 16874 : 2018 | Protective gloves for firefighters |
| 405 | IS 15748 : 2022 | Protective clothing for industrial workers exposed to heat |
| 406 | IS 15742 : 2007 | Clothing made of limited flame spread materials and material assemblies affording protection against heat and flame |
| 407 | IS 15809 : 2017 | High visibility Warning Clothes |
| 408 | IS 16655 : 2017 | Protective Clothing for use in welding and allied processes |
| 409 | IS 16725 : 2018 | Tactical 3 point sling |
| 410 | IS 16726 : 2018 | Pouch for ammunition and grenades made of disruptive pattern nylon-66 |
| 411 | IS 17051 : 2018 | Bullet resistant jackets |
| 412 | IS 17286 : 2019 | Water-proof multipurpose rain poncho |
| 413 | IS/ISO 9994:2018 | Lighters- Safety Specifications |
| 414 | IS/ISO 22702:2018 | Utility Lighters – Safety Specifications |
| 415 | IS 17803: 2022 | Potable Water Bottles (Copper, Stainless Steel, Aluminum) |
| 416 | IS 814 : 2004 | Covered electrodes for manual metal arc welding of carbon and carbon manganese steel |
| 417 | IS 6419 : 1996 | Welding rode and bare electrodes for gas shielded arc welding of structural steel |
| 418 | IS 16444 Part 1 | A.C. Static Direct Connected Watt Hour Smart Meter Class 1 and 2 |
| 419 | IS 16444 Part 2 | A.C. Static Transformer Operated Watt Hour and Var-Hour Smart Meters, Class 0.2S, 0.5S and 1.0S |
| 420 | IS 17790 : 2022 | Insulated Flask for Domestic Use |
| 421 | IS 17526 : 2021 | Domestic Stainless steel vacuum flask/bottle |
| 422 | IS 17569: 2021 | Insulated Container for Food Storage |
| 423 | IS 3513 (Part 1) : 1989 | Resin treated compressed wood laminates (compregs) – For electrical purposes |
| 424 | IS 3513 (Part 2) : 1989 | Resin treated compressed wood laminates (compregs) – For chemical purposes |
| 425 | IS 3513 (Part 3) : 1989 | Resin treated compressed wood laminates (compregs) – For general purposes |
| 426 | IS 1363 (Part 1) :2019 | Hexagon Head Bolts, Screws and Nuts of product Grade C Hexagon Head Bolts (Size Range M 5 to M 64) |
| 427 | IS 1363 (Part 2) :2018 | Hexagon Head Screw (Size ranges from M 5 to 64) |
| 428 | IS 1363 (Part 3) :2018 | Hexagon Head Bolts, Screws and Nuts of product Grade C – Hexagon Nuts (Size Range M5 to M64) |
| 429 | IS 1364 (Part 1) :2018 | Hexagon Head Bolts, Screws and Nuts of product Grades A and B – Hexagon Head Bolts (Size Range M 1.6 To M 64) |
| 430 | IS 1364 (Part 2) :2018 | Hexagon Head Bolts, Screws and Nuts of Product Grades A and B – Hexagon Head Screws (Size Range M 1.6 to M 64) |
| 431 | IS 4621:1975 | Indicating Bolts for use in public baths and lavatories |
| 432 | IS 5187: 1972 | Flush Bolts |
| 433 | IS 10238:2001 | Fasteners – Threaded Steel Fastener – Step Bolts for Steel Structures |
| 434 | IS 12427 : 2001 | Fasteners – Threaded Steel Fasteners – Hexagon Head Transmission Tower Bolts |
| 435 | IS 3757 : 1985 | High Strength Structural Bolts |
| 436 | IS 204 (Part 2): 1992 | Tower Bolts- Non-ferrous metal |
| 437 | IS 204 (Part 1): 1991 | Tower Bolts- Ferrous metals |
| 438 | IS 15834 : 2022 | Stainless Steel Sliding Door Bolts (Aldrops) for use With Padlocks |
| 439 | IS 2681 : 1993 | Non-ferrous metal sliding door bolts (aldrops) for use with padlocks |
| 440 | IS 281 : 2009 | Mild steel sliding door bolts for use with padlocks |
| 441 | IS 7534: 1985 | Sliding locking bolts for use with padlocks |
| 442 | IS 1284 : 1975 | Wrought Aluminium Alloy Bolt and Screw Stock for General Engineering purposes |
| 443 | IS 15833 : 2009 | Stainless steel Tower Bolts |
| 444 | IS 6623 : 2004 | High Strength Structural Nuts |
| 445 | IS 14756 : 2022 | Stainless Steel Cookware |
| 446 | IS 1660:2009 | Wrought Aluminium Utensils |
| 447 | IS 13983:1994 | Stainless Steel Sinks for Domestic Purposes |
| 448 | IS 9396 (Part 1) : 1987 | Round Open Top Sanitary Cans for Foods and Drinks – Tinplate |
| 449 | IS 14407:1996 | Aluminium cans for beverages |
| 450 | IS 17153:2019 | Domestic Gas Stoves for use with Piped Natural Gas (PNG) |
| 451 | IS 15683 : 2018 | Portable Fire Extinguishers |
| 452 | IS 16018:2012 | Wheeled Fire Extinguishers |
| Electric Ceiling Type Fans | ||
| 453 | IS 374:2019 | Electric Ceiling Type Fans |
| Wood Based Boards | ||
| 454 | IS 1659:2004 | Block Boards |
| 455 | IS 12823:2015 | Prelaminated particle boards from wood and other Lignocellulosic material |
| 456 | IS 3087:2005 | Particle boards of wood and other lignocellulosic materials (medium density) for general purpose |
| 457 | IS 12406:2021 | Medium density fibre boards for general purpose |
| 458 | IS 3097:2006 | Veneered particle boards |
| Cast Iron Products | ||
| 459 | IS 1726:1991 | Cast iron man hole covers and frames |
| 460 | IS 1729:2002 | Cast iron/ductile iron drainage pipes and pipe fittings for over ground non-pressure pipelines socket and spigot series |
| 461 | IS 1879:2010 | Malleable cast iron pipe fittings |
| 462 | IS 13349:1992 | Cast iron single faced thimble mounted sluice gates |
| 463 | IS 210:2009 | Grey iron castings |
| 464 | IS 1537:1976 | Vertically cast – iron pressure pipes for water, gas and sewage |
| Solar DC Cable and Fire Survival Cable | ||
| 465 | IS 17293:2020 | Electric Cable for Photovoltic Systems for rated voltage 1500V DC |
| 466 | IS 17505(Part 1): 2021 | Thermosetting Insulated, Fire Survival Cables for working voltage upto and including 1100V AC and 1500V DC |
| Metals and Alloys | ||
| 467 | IS 617:1994 | Cast aluminium and its alloys – Ingots and castings for general engineering purposes |
| 468 | IS 11890 : 1987 | High purity primary aluminum ingot for remelting for special applications |
| 469 | IS 6754:1972 | Aluminum alloy ingots for remelting for general engineering purpose |
| 470 | IS 2590 : 1987 | Primary aluminium ingots for remelting for general engineering purpose |
| 471 | IS 4026 : 2023 | Aluminum ingots billets and wire bars (EC GRADE) |
| 472 | IS 191:2007 | Copper |
| 473 | IS 7506:1987 | Nickel Powder |
| Plywood and Wooden flush door shutters | ||
| 474 | IS 303 : 1989 | Plywood for general purposes |
| 475 | IS 2202 (Part 1) : 1999 | Wooden flush door shutters (solid core type) – Plywood face panels |
| 476 | IS 710 : 2010 | Marine plywood |
| 477 | IS 5509 : 2021 | Fire retardant plywood |
| 478 | IS 1328 : 1996 | Veneered decorative plywood |
| 479 | IS 2191 (Part 2): 2022 | Wooden flush door shutters (cellular and hollow core type) – Particle board and hardboard face panels |
| 480 | IS 2191 (Part 1): 2022 | Wooden flush door shutters (cellular and hollow core type) – Plywood face panels |
| 481 | IS 2202 (Part 2): 2022 | Wooden Flush Door Shutters (Solid core type) – Particle board, High Density Fibre Board, Medium Density Fibre Board and Fibre Hardboard Face Panels |
| 482 | IS 4990 : 2011 | Plywood for concrete shuttering works – Specification |
| 483 | IS 10701 : 2012 | Structural plywood – Specification |
| Flux Cored Solder Wire | ||
| 484 | IS 1921: 2005 | Flux Cored Solder Wire |
| Miscellaneous Steel Products | ||
| 485 | IS 15155 : 2020 | Bar or wire Wrapped Steel Cylinder Pipes with Mortar Lining and Coating Including Specials |
| 486 | IS 16651 : 2017 | High Strength deformed stainless steel bars and wires for concrete reinforcement |
| 487 | IS 6392 : 2020 | Steel Pipe Flanges |
| 488 | IS 6913 : 1973 | Stainless steel tubes for the food and beverage industry |
| Aluminium and Aluminium Alloy Products | ||
| 489 | IS 7092 (Part 1):1992 | Aluminium alloy tubes for irrigation purposes -welded tubes |
| 490 | IS 7092 (Part 2):1987 | Aluminium alloy tube for irrigation purposes – extruded tube |
| 491 | IS 5484:1997 | EC Grade Aluminium Rod produced by Continuous Casting and Rolling |
| 492 | IS 733:1983 | Wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) |
| 493 | IS 734:1975 | Wrought aluminium and aluminium alloys, forging stock and forgings for general engineering purposes |
| 494 | IS 736:1986 | Wrought aluminium and aluminium alloy plate for general engineering purposes |
| 495 | IS 737:2008 | Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes |
| 496 | IS 739:1992 | Wrought aluminium and aluminium alloy wire for general engineering purposes |
| 497 | IS 740:1977 | Wrought aluminium and aluminium alloy rivet stock for general engineering purposes |
| 498 | IS 5082:1998 | Wrought aluminium and aluminium alloy bars, rods, tubes, sections, plates and sheets for electrical applications |
| 499 | IS 16011:2012 | Aluminium and aluminium alloy foil for pharmaceutical packaging |
| 500 | IS 17682:2021 | Aluminium composite panel |
| 501 | IS 1285:2002 | Wrought aluminium and aluminium alloys- Extruded round tube and hollow sections for general engineering purposes |
| 502 | IS 2067:1975 | Wrought Aluminium Wire for Electrical Purposes |
| 503 | IS 21:1992 | Wrought aluminium and aluminium alloys for manufacture of utensils |
| 504 | IS 1254:2007 | Corrugated Aluminium Sheet |
| 505 | IS 7902:2001 | Aluminium alloy forging stock and forgings (Alloy 24345) for aerospace applications |
| 506 | IS 2403 :2014 / ISO 606 : 2004 | Short – Pitch Transmission Precision Roller and Bush Chains, Attachments and Associated Chain Sprockets |
| Self- Contained Drinking Water Coolers | ||
| 507 | IS 1475 (Part 1) : 2001 | Self- Contained Drinking Water Coolers – Energy Consumption and Performance |
| Medical Textiles | ||
| 508 | IS 5405 : 2019 | Sanitary napkins |
| 509 | IS 17509 : 2021 | Disposable baby diaper |
| 510 | IS 17514 : 2021 | Reusable Sanitary pad/ Sanitary Napkin/ Period Panties |
| 511 | IS 17349 : 2020 | Shoe covers |
| 512 | IS 17354 : 2020 | Dental Bib or Napkins |
| 513 | IS 17630 : 2021 | Bed sheet and Pillow Cover |
| Agro Textiles | ||
| 514 | IS 16718 : 2021 | Polypropylene Spun Bonded Non—Woven Crop Cover and Fruit Skirting Bags for Agriculture and Horticulture Applications |
| 515 | IS 16513 : 2016 | Insect nets for Agriculture and Horticulture purpose |
| 516 | IS 16202 : 2014 | Woven Ground covers for Horticulture Application |
| 517 | IS 17070 : 2019 | Jute Agro textiles for Growth of Plants and Suppression of Weeds |
| 518 | IS 15907 : 2010 | High Density Polyethylene (HDPE) woven beds for vermiculture |
| 519 | IS 16089 : 2013 | Sapling bags for growth of seedling /sapling |
| 520 | IS 16190 : 2014 | High Density Polyethylene (HDPE) laminated woven lay flat tube for irrigation purpose |
| 521 | IS 16390 : 2015 | Nylon Knitted seamless gloves for tobacco harvesters |
| 522 | IS 16627 : 2017 | High density polyethylene (HDPE) laminated woven lay flat tube for use in mains and submains of drip irrigation system |
| 523 | IS 17355 : 2020 | Propylene Spun bonded non—woven mulch mat for agriculture and horticulture applications |
| 524 | IS 17356 : 2020 | Windshield nets for agriculture and horticulture purpose |
| 525 | IS 17357 : 2020 | Harvest nets for agriculture and horticulture purposes |
| 526 | IS 17358 (Part 1) : 2020 | Fencing nets for agriculture and horticulture purposes – made from extruded polymer mesh |
| 527 | IS 17358 (Part 2) : 2020 | Fencing nets for agriculture and horticulture purposes -made from mono filament yarns and combination of tape and mono filament yarns |
| 528 | IS 17513 : 2020 | Plant Support Nets for Agriculture and Horticulture Purposes |
| 529 | IS 17728 : 2021 | High Density Polyethylene (HDPE) Laminated Woven Lay Flat Tube and Fittings for use in Rain Irrigation System |
| 530 | IS 17729 : 2021 | Flexible Water Storage Tank for Agriculture and Horticulture Purposes |
| 531 | IS 17730 (Part 1) : 2021 | Hail Protection Nets for Agriculture and Horticulture Purposes- Warp Knitted Hail Protection Nets |
| 532 | IS 17730 (Part 2) : 2021 | Hail Protection Nets for Agriculture and Horticulture Purposes – Woven Hail Protection Nets |
| 533 | IS 17731 : 2021 | Laminated Woven Orchard Protection Covers |
| Copper Products | ||
| 534 | IS 12444:2020 | Copper Wire Rods for Electrical Applications |
| 535 | IS 613:2000 | Copper Rods and Bars for Electrical Purposes |
| 536 | IS 1897:2008 | Copper strip for electrical purposes |
| 537 | IS 4171:1983 | Copper rods and bars for general engineering purposes |
| 538 | IS 1545: 1994 | Solid drawn copper and copper alloy tubes for condensers and heat exchangers |
| 539 | IS 2501: 1995 | Solid drawn copper tubes for general engineering purposes |
| 540 | IS 14810: 2000 | Copper Tubes for plumbing- Specification/p> |
| 541 | IS 10773:1995 | Wrought Copper Tubes for Refrigeration and Air- Conditioning Purpose |
| 542 | IS 4412:1981 | Copper wires for general engineering purposes |
| Drums and Tins | ||
| 543 | IS 13997:2014 | Drums, Large Open Top |
| 544 | IS 1783 (Part 1) :2014 | Drums Large, Fixed Ends – Grade A |
| 545 | IS 1783 (Part 2) :2014 | Drums, Large, Fixed Ends – Grade |
| 546 | IS 2552:1989 | Steel Drums (Galvanized and Ungalvanized) |
| 547 | IS 3575:1993 | Bitumen Drums |
| 548 | IS 916:2000 | Square Tins for Solid Products |
| 549 | IS 10325:2000 | Square Tins – 15 Kilograms or litre for Ghee, Vanaspati, Edible Oils and Bakery |
| Door Fittings | ||
| 550 | IS 6343:1982 | Door closers (pneumatically regulated) for light doors weighing up to 40 kg |
| 551 | IS 14912:2001 | Door closers, concealed type (hydraulically regulated) |
| 552 | IS 3564:1995 | Hydraulically Regulated Door Closers |
| 553 | IS 6315:1992 | Floor springs (hydraulically regulated) for heavy doors |
| 554 | IS 1019:1974 | Rim Latches |
| 555 | IS 208:2020 | Door Handles |
| 556 | IS 4992:1975 | Door handles for mortice lock (vertical type) |
| Bottled Water Dispenser | ||
| 557 | IS 17681:2022 | Bottled water dispensers |
| Helmet for Police Force, Civil Defence and Personal Protection | ||
| 558 | IS 2745:1983 | Non-metal helmet for firemen and civil defence personnel |
| 559 | IS 2925:1984 | Industrial safety helmets |
| 560 | IS 9562:1980 | Non- metal helmet for Police Force |