HZLAB20210811返回 Back
土耳其
EN 10204 钢结构
| SCOPE OF ACCREDITATIONS | |||
|
Inspection type |
Inspection field / sub-field(s) |
Stage of inspection (e.g. Fabrication, In-service…) |
Inspection requirements / criteria |
|
Periodic Control |
1. Lifting and Forwarding Machines 1.A.1. Crane -1.A.1.1. Overhead Crane -1.A.1.2. Portal Crane -1.A.1.3. Monorail Crane -1.A.1.4. Mobile Crane -1.A.1.5. Tower crane -1.A.1.6. Loader Crane 1.A.2. Caraskal 1.A.3. Platform -1.A.3.1. Upgradeable Mobile Work Platform -1.A.3.3. Hanging Access Hardware -1.A.3.4. Columnar Work Platform 1.A.4. Vehicle Lifting Equipment 1.A.8. Transportable 1.A.10. Forklifts 1.A.11. Escalator 1.A.12. Walking Tape 1.A.19. Construction Lift |
Fabrication, In-service |
Regulation 28628 Republic of Turkey - Health And Safety Regulations Terms of Use of Work Equipment |
|
Periodic Control |
2. Pressure Vessels 2.A.1. Industrial Autoclave 2.A.2. Compressed Air Tank 2.A.3. Compressor Air Tank 2.A.4. Hydrophore / Expansion Tank 2.A.7. Liquefied Gas Tanks 2.A.8. Cryogenic Tanks |
Fabrication, In-service |
Regulation 28628 Republic of Turkey - Health And Safety Regulations Terms of Use of Work Equipment |
|
Periodic Control |
3. Boilers 3.A.1. Steam boiler 3.A.2. Heating / Hot Water Boiler 3.a.4. Hot Oil Boiler 3.A.7. Hot Water Boiler |
Fabrication, In-service |
Regulation 28628 Republic of Turkey - Health And Safety Regulations Terms of Use of Work Equipment |
|
Periodic Control |
4.A.1. Atmospheric Storage Tanks |
Fabrication, In-service |
Regulation 28628 Republic of Turkey - Health And Safety Regulations Terms of Use of Work Equipment |
|
Periodic Control |
5. Fire Protection Systems 5.a.1. Sprinkler Systems 5.A.2. Fire Water Tank 5.A.3. Fire Pumping Station 5.A.4. Fire Hydrant System 5.A.5. Fire Cabinet System 5.A.6. Water Spray Systems 5.A.7. Water Mist Systems 5.A.8. Foam Extinguishing Systems 5.A.9. Portable Fire Extinguisher Tubes 5.A.10. Detection Alarm Systems 5.A.11. Automatic Gas Extinguishing Systems 5.A.12. CO2 Gas Automatic Extinguishing Systems. 5.A.13. Dry /Liquid Chemical Extinguishing Systems 5.A.14. Emergency Lighting and Routing Systems 5.A.15. Smoke Evacuation Systems 5.A.16. Escape Systems Pressurization Systems |
Fabrication, In-service |
Regulation 28628 Republic of Turkey - Health And Safety Regulations Terms of Use of Work Equipment |
|
Periodic Control |
Lifts: - Electric Drive Lift - Hydraulic driven elevator |
Fabrication, In-service |
Republic of Turkey - Elevator Operating, Maintenance and Periodic Control Regulation Republic of Turkey - Communiqué on Type A Inspection Bodies to be Authorized for Elevator Periodic Controls |
|
First Inspection |
5. Fire Protection Systems 5.C.1. Sprinkler Systems 5.C.2. Fire Water Tank 5.C.3. Fire Pumping Station 5.C.4. Fire Hydrant System 5.C.5. Fire Cabinet System 5.C.6. Water Spray Systems 5.C.7. Water Mist Systems 5.C.8. Foam Extinguishing Systems 5.C.9. Portable Fire Extinguisher Tubes 5.C.10. Detection Alarm Systems 5.C.11. Automatic Gas Extinguishing Systems 5.C.12. CO2 Gas Automatic Extinguishing Systems 5.C.13. Dry / Liquid Chemical Extinguishing Systems 5.C.14. Emergency Lighting and Routing Systems 5.C.15. Smoke Evacuation Systems 5.C.16. Escape Systems Pressurization Systems |
Fabrication, In-service |
TS ISO 14520-11 TS EN 14466- A1 TS EN 12845 NFPA 25 NFPA 2001 NFPA 12 |
|
Process Inspection |
Welded Manufacturing - Evaluation and Approval of Welding Procedures |
Fabrication, In-service |
AD 2000 Merkblatt HP2 / 1 ASME Sec.IX ASTM A488 TS EN ISO 15614 AWS D1.1 AWS D1.5 API 1104 TS EN 1090-2 |
|
Process Inspection |
Steel Structures - Manufacturing Process Inspection |
Fabrication, In-service |
AWS D1.1 AWS D1.5 TS EN 1090-2 |
|
Non-Destructive Testing (NDT) |
Gas and Liquid Petroleum Products (LPG) Storage Tanks and Pipelines: Acoustic Emission Measurements |
Fabrication, In-service |
Regulation 28628 REPUBLIC OF TURKEY - HEALTH AND SAFETY REGULATIONS TERMS OF USE OF WORK EQUIPMENT TS EN 12817 TS EN 12819 TS EN 13554 TS EN 15495 ASTM E1930-97 ASME Sec.V |
|
Non-Destructive Testing |
Acoustic Emission Test |
Fabrication, In-service |
TS EN ISO 7317 TS EN 13477-1 TS EN 13477-2 TS EN 13554 TS EN 15495 TS EN 14584 ASTM E569-07 ASTM E1930- 97 TS EN ISO16148 TS EN 15856 ASME BPVC Sect. 5 2013 |
|
Non-Destructive Testing |
Radiographic Examination, Evaluation and Approval of Films |
Fabrication, In-service |
TS EN ISO 17636-1 TS EN ISO 17636-2 TS EN ISO 5817 TS EN ISO 10675-1 TS EN ISO 10675-2 TS EN 12681 TS EN ISO 5579 97/23 / A1 AT API 650 AWS D1.1 AWS D. 1.5 ASME SEC V ASME B 31.1 ASME 31.3 ASME B 31.8 ASME SEC. VIII API 1104 AD 2000 markers HP5 / 3 |
|
Non-Destructive Testing |
Liquid Penetrant Inspection, Evaluation and Approval |
Fabrication, In-service |
TS EN ISO 5817 TS EN ISO 3452-1 TS EN ISO 23.277 TS EN 10.228-2 TS EN 1371-1 TS EN 1371-2 API 650 AWS D.1.1 AWS D.1.5 ASME SEC V ASME B 31.1 ASME B 31.3 ASME B 31.8 ASME SEC VIII API 1104 |
|
Non-Destructive Testing |
Magnetic Particle Inspection Evaluation and Approval |
Fabrication, In-service |
5817 TS EN ISO TS EN ISO 17638 TS EN ISO 23278 TS EN 10.228-1 API 650 AWS D.1.1 AWS D.1.5 ASME SEC V ASME B 31.1 ASME B 31.3 ASME B 31.8 ASME SEC VIII API 1104 |
|
Non-Destructive Testing |
Inspection, Evaluation and Approval by Ultrasonic Inspection, Phased Array & TOFD Techniques |
Fabrication, In-service |
TS EN ISO 5817 TS EN ISO 11666 TS EN ISO 23279 TS EN ISO 17640 TS EN 10228-3 TS EN 12.680-1 API 650 AWS D1.1 AWS D.1.5 ASME SEC V ASME B 31.1 ASME B 31.3 ASME B 31.8 ASME SEC VIII API 1104 |
|
Non-Destructive Testing |
Metal products and metal products manufacturing – Visual Inspection |
Fabrication, In-service |
TS EN ISO 5817 TS EN ISO 17637 API 1104 API 650 AWS D.1.1 AWS D.1.5 ASME V ASME B 31.1 ASME B 31.3 ASME B 31.8 ASME SEC VIII |
|
Electrical Measurements and Evaluation |
-Grounding- Lightning Rod Measurement and Control - Cathodic Protection Measurements - Generator |
Fabrication, In-service |
REPUBLIC OF TURKEY - Grounding Regulation for Electrical Installations, TS EN 62305-1 TS EN 62305-3 TS EN 12817 TS EN 12819 Regulation 28628 REPUBLIC OF TURKEY -Regulation on Health and Safety Conditions in the Use of Work Equipment |
|
Radiation Control |
Metallurgical Scrap |
Fabrication, In-service |
TAEK Regulation on Radiation Safety Communiqué on the Status of International Surveillance Company (Product Safety and Inspection: 2015/24) 15.01.02.PR.04 Radiation Control Inspection Procedure in Metal Scrap |
|
Non-Destructive Testing |
- Packed Products - Textile products - Machinery and mechanical devices and parts thereof - Electrical and Electronic Equipment and parts thereof - Electrical Equipment - Elevators and their accessories - Chemicals, hygienic products, cleaning products, personal care products etc. - Pressure vessels and equipment - Road vehicles and parts thereof - Ceramic and Plastic Products - Composite materials, wood and casting products - Articles of ordinary metals and basic metals - Various Goods (Furniture, Toys, Games and Sporting Goods, parts thereof, miscellaneous goods, etc.) |
Fabrication, In-service |
MGMB work instructions |
|
Cargo inspection |
Transported by sea, land and railway vehicles and containers; Solid bulk cargoes; - Mining and Mineral Products - Ferro Alges Gas and Liquid Loads; - Crude oil - Petroleum Products - Chemicals |
Fabrication, In-service |
MGMB work instructions API MPMS Part 12 HM28-HM29 TS ISO 2859-1 TS ISO 2859-2 TS ISO 2859-3 TS ISO 2859-4 TS ISO 2859-5 |
|
Cargo inspection |
-Agricultural products - Vegetable Oils |
Fabrication, In-service |
MGMB work instructions Sampling Rules (GAFTA, FOSFA, ICA, TS, Food Codex, IWTO, FCC, OIE etc.) |
|
Manufacturing Process Inspection |
Machined Parts - Sheets - Pipes - Valves |
Fabrication, In-service |
TS EN 10204 TS EN 10217 TS EN 10219-1 TS EN 10219-2 TS EN 10025 series TS EN 10028 series TS EN 10149 series TS EN ISO 3183 TS EN 13942 ASTM A 36 ASTM A 53 ASTM A 106 ASTM A 333 ASTM A 312 ASTM A 283 ASTM A 516 ASTM A 517 ASME B16.34 API 602 API 6D API 598 API 600 API 5L API 610 DIN 1626 |
|
Periodic examination |
-Thermographic examination - I-V measurement and degredation analysis Networked Photovoltaic Systems - Photovoltaic (PV) Modules - Inverters - Solar Cables |
Fabrication, In-service |
TS EN 62446-1 IEC 62446-1 IEC 62446-3 TS EN 61724 TSE-MGMB inspection procedure TS EN 62759-1 IEC 62759-1 IEC 62759-2 |
|
Post-installation Surveillance - Annual Main Inspection |
Children Playground Elements and Ground Arrangements |
Fabrication, In-service |
TS EN 1176-1 TS EN 1176-1 / D1 TS EN 1176-2 TS EN 1176-3 TS EN 1176-3 / D1 TS EN 1176-4 TS EN 1176-5 TS EN 1176-6 TS VE 1176-7 TS EN 1176-11 |
|
Periodic Control |
Speed Measuring Instruments (RADAR) |
Fabrication, In-service |
Speed Violation Fixing Equipment Inspection Regulation |
|
Initial inspection |
Pressure Equipment Assessment and Approval of Fixed Connection Procedures |
Fabrication, In-service |
2014/68 / EU Pressure Equipment Directive Annex I Article 3.1.2 & 3.1.3 |
| NDT |
Steel Wire Rope Inspection |
Fabrication, In-service |
TS EN 12385-1 ASTM E1571 |
| NDT |
Medical and Protective Mask inspection-Visual and Measurement Inspection Type Approval |
Fabrication, In-service |
93/42/EEC EU Medical Directive (EU) 2017/745 (EU)2016/425 Personal Protective Directive |
| NDT |
Medical and Protective Gown Suits inspection-Visual and Measurement Inspection Type Approval |
Fabrication, In-service |
93/42/EEC EU Medical Directive (EU) 2017/745 (EU)2016/425 Personal Protective Directive |
| NDT |
Disinfectant Products inspectionVisual and Measurement Inspection Type Approval |
Fabrication, In-service |
93/42/EEC EU Medical Directive (EU) 2017/745 (EU)2016/425 Personal Protective Directive |
| NDT |
Electromagnetic compatibility examination of electrical and electronic devices-Visual and Measurement Inspection Type Approval |
Fabrication, In-service |
2014/30/EU, Electromagnetic Compatibility Directive |
| NDT |
Low voltage Electrical Equipment Inspection-Visual and Measurement Inspection Type Approval |
Fabrication, In-service |
2014/35/EU Low voltage directive |
| NDT |
Electrical parts, Metal Parts, Composite Parts inspection- Visual and Measurement Inspection Type Approval |
Fabrication, In-service |
ECE/UNECE Regulations |
| NDT |
XRF Mining Metal Alloys InspectionMeasurement Inspection Type Approval |
Fabrication, In-service |
Inhouse Method |
| NDT |
Equipment Inspections and Type Approval - Metal, Composite, Electronic Parts and Glass for specific Use by Customers Like Military and Air Space Industries |
Fabrication, In-service |
Customer Specific Standards, other International applicable inspection standards and Inhouse Method |
| NDT |
Construction Product Inspections and Type Approval - Metal, Composite, Concrete and Glass |
Fabrication, In-service |
EU 305/2011 89/106/EEC |
| NDT |
Medical Respirator Inspection and Type Approval |
Fabrication, In-service |
93/42/EEC EU Medical Directive (EU) 2017/745 |
| standard | Test Contents |
| SAE AMS-2700 | Humidity |
| SAE AMS-STD 753 | Humidity |
| SAE AMS-STD-753 | Salt Spray (Fog) |
| SAE J 1742 | Connections for High-Voltage On-Board Electrical Harnesses - Test Methods and General Performance Requirements |
| SAE J 1756 | Determination of Fogging Properties of Interior Automotive Materials |
| SAE J 1960 | Accelerated exposure of automotive exterior materials using a controlled irradiation water-cooled Xenon arc apparatus |
| SAE J 2302 | Thermal Efficiency of Coupling / Hose / Band Insulation |
| SAE J 2334 | Laboratory cyclic corrosion test |
| SAE J 2527 | Performance-based standard for accelerated exposure of automotive exterior materials using a controlled radiation Xenon-arc apparatus |
| SAE J 2635 | Threadlike corrosion test procedure for painted aluminum wheels and painted aluminum wheel trim |
| SAE J 343 -SAE 100R | Series Hydraulic Hoses and Trousers |
| SAE J 365 | Method for Testing the Friction Resistance of Trim Materials |
| SAE J 684 | Surface vehicle standard; Tests for balls and trailer couplings |
| SAE J1113-1 | Electromagnetic Compatibility Measurements procedures and limits for vehicle co |
| SAE J1113-11 | Immune to Transient Transients Conducted on Power Cables |
| SAE J1113-12 | Electrical Interference from Transmission and Coupling ? Capacitive and Inductive Coupling on Lines Except for Supply Lines |
| SAE J1113-13 | Electromagnetic Compatibility Measurement Procedure for Vehicle Components? Chapter 13: Immunity to Electrostatic Discharge |
| SAE J1113-2 | Electromagnetic Compatibility Measurement Procedures and Limits for Vehicle Components (Excluding Aircraft)-Conducted Immunity, 15 Hz - 250 kHz-All Leads |
| SAE J1113-21 | Electromagnetic Compatibility Measurement Procedure for Vehicle Components? Chapter 21: Immunity to Electromagnetic Fields, 30 MHz - 18 GHz, Absorber Striped Chamber |
| SAE J1113-22 | Electromagnetic Compatibility Measurements Procedure for Vehicle Components ? episode 22? Immunity to Radiated Magnetic Fields |
| SAE J1113-23 | Electromagnetic Compatibility Measurement Procedure for vehicle components ? Immunity to Radiated Electromagnetic Fields, 10 kHz - 200 MHz, Strip Line Method |
| SAE J1113-24 | Immunity to Radiated Electromagnetic Fields; 10 kHz - 200 MHz ? Crawford TEM Cell and 10 kHz to 5 GHz? Broadband TEM Cell |
| SAE J1113-26 | Electromagnetic Compatibility Measurement Procedure for Vehicle Components? Immunity to AC Power Line Electric Fields |
| SAE J1113-3 | Conducted Immunity, 250 kHz - 400 MHz, Direct Injection of Radio Frequency (RF) Power |
| SAE J1113-4 | Immunity Against Radiated Electromagnetic Fields Bulk Current Injection (BCI) Method |
| SAE J1113-41 | Limits and Measurement Methods of Radio Distortion Characteristics of Components and Modules for the Protection of Aircraft Receivers |
| SAE J1113-42 | Electromagnetic Compatibility Component Test Procedure Part 42 Conducted Transient Emissions |
| SAE J1127 | Low voltage battery cable |
| SAE J1128 | Low voltage primary cable |
| SAE J1211 | Recommended Environmental Practices for Electronic Equipment Design |
| SAE J1237 | Hardness |
| SAE J1326 | Measurement of Wet Color Transfer Properties |
| SAE J1351 | Odor |
| SAE J1352 | Compression and Recovery of Insulation Fills |
| SAE J1355 | Test Method for Measuring the Thickness of Flexible Insulation Fillers |
| SAE J1389 | Corrosion Test for Insulation Materials(STABILIZED August 2011) |
| SAE J1402 | Automotive Air Brake Hose and Hose Groups |
| SAE J1455 | Common SAE/TMC Recommended Environmental Practices for Electronic Equipment Design (Heavy Duty Trucks) |
| SAE J1523 | Metal-to-Metal Shear Strength Test for Automotive Type Adhesives |
| SAE J1525 | Lap Shear Test for Automotive Type Adhesives for Fiber Reinforced Plastic (Frp) Bonding |
| SAE J1530 | Abrasion (Taber, Schopper and Wyzenbeek) |
| SAE J1530-A | Fiber Loss Resistance Erichsen Scratch Resistance |
| SAE J1531 scratch resistance | (Taber Abrasion Only) -Scratch/ Scratch/ Scuffing/ Smearing/ Mar Resistance Scratch Resistance (Five Fingers) Fiber Loss Resistance Erichsen Scratch |
| SAE J1531-A | Fiber Loss Resistance Erichsen Scratch Resistance |
| SAE J1545 | Instrumental Color Difference Measurement for Exterior Cladding, Textiles and Colored Flooring |
| SAE J1545- J1717 (Annex E) | Color Measurements Instrumental, sphere |
| SAE J1553 | Cross Peel Test for Automotive Type Adhesives for Fiber Reinforced Plastic (Frp) Bonding |
| SAE J1600 (4/87) | Evaluation of Adhesion Properties of Automotive Sealants (Cancelled January 2001) |
| SAE J1625 | Heavy Duty Circuit Breakers |
| SAE J1639 | Test Methods for Nylon Materials |
| SAE J1679 | Adhesion/Cohesion and Peel Strength |
| SAE J17 | Latex Foam Rubbers |
| SAE J1717 | Interior Automotive Plastic Part Test(NOT PASSED November 2007) |
| SAE J1717 (Appendix E) | Brightness/Turbidity Measurements |
| SAE J1717-D1 | Pendulum Strike |
| SAE J1752-3 | Measurement of Radiated Emissions from Integrated Circuits – TEM / Broadband TEM (GTEM) Cell Method; TEM Cell (150 kHz - 1 GHz), Broadband TEM Cell (150 kHz - 8 GHz) |
| SAE J1756 | Fogging |
| SAE J1756-A | Fogging |
| SAE J1756-B | Fogging |
| SAE J1757-A | Fogging |
| SAE J1757-B | Fogging |
| SAE J1767 | Instrumental Color Difference Measurements for Color Fastness of Automotive Interior Upholstery Materials |
| SAE J1769 | SAE Fact Sheet - Protocol for the Long-Term Evaluation of Permeability - Barrier Strength in Non-Metallic Fuel Tanks |
| SAE J1798 | Rating of Electric Vehicle Battery Modules |
| SAE J1847 | Wear Resistance Test-Vehicle Exterior Graphics and Pin Lines |
| SAE J1885 | Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Radiation Water-Cooled Xenon-Arc Apparatus |
| SAE J1885 (3/05) | Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Radiation Water-Cooled Xenon-Arc Apparatus (Canceled Jan 2008, Replaced By J2412_201508) |
| SAE J1885 (Inactive 2008) | Accelerated Exposure of Automotive Interior Trim Components Using Controlled Radiation Water Cooling |
| SAE J1885-05 | Accelerated Exposure of Automotive Interior Trim Components |
| SAE J1885 | Indoor (replaced Jan 2008) -Color Fastness -Xenon Arc |
| SAE J1907 | Glass-to-Elastomeric Peel Adhesion Test for Automotive Glass Encapsulation |
| SAE J1960 | Accelerated Exposure of Automotive Exterior Materials Using a Controlled Radiation Water-Cooled Xenon-Arc Apparatus |
| SAE J1960 | ( 10/04 - Accelerated Exposure of Automotive Exterior Materials Using a Controlled Radiation Water Cooled Xenon Arc Apparatus (Cancelled Jan 2008, Replaces J2527) |
| SAE J1960 (Inactive 2008) | Xenon Arc Time-Lapse Exposure (External) |
| SAE J1960-04 | Accelerated Exposure of Automotive Exterior Materials Using a Controlled Radiation Water-Cooled Xenon-Arc Apparatus |
| SAE J1961 | Accelerated Exposure of Automotive Exterior Materials Using Solar Reflector Apparatus |
| SAE J1976 | Outdoor Decomposition of Outdoor Materials |
| SAE J2016 (11/99) | Chemical Stress Resistance of Polymers (Cancelled in February 2008, Replaced by ISO 11403-3) |
| SAE J2020 | Accelerated Exposure of Automotive Exterior Materials Using Fluorescent UV and Condensation Apparatus |
| SAE J2027 | Standard for Protective Caps for Gasoline Fuel Line Pipes, Chemical Resistance (Xenon-Arc) |
| SAE J2044 | Quick Connect Coupling Specification for Fuel Oil and Vapor/Emission Systems |
| SAE J2045 (Chapter 4.5) | Internal Fuel Resistor |
| SAE J2045 (Chapter 4.6) | Internal Fuel Resistor |
| SAE J2045 (Chapter 7.8) | Resistance to auto-oxidized fuel |
| SAE J2060 (Chapter 7.8) | Resistance to auto-oxidized fuel |
| SAE J2060 (Chapter 7.9) | Resistance to auto-oxidized fuel |
| SAE J2100 | Temperature and Humidity Temperature Range; (-100 to 180) °C, Humidity Range ; 5 to 100% RH, (5-90%RH ; ±1.0%RH, 90-100%RH ; ±1.7%RH 15 to 50°C) |
| SAE J2114 | Wear resistance (Taber) |
| SAE J2215 | Adhesion/Cohesion and Peel Strength |
| SAE J2236 | Determination of Continuous Upper Temperature Resistance of Elastomers |
| SAE J2253 | Test Procedures for Automotive Structural Composite Materials (Formerly ACCM-T-02) |
| SAE J2260 (Section 7.6) | Fuel Exposure preconditioning |
| SAE J2260 (Chapter 7.7) | Methanol Resistance |
| SAE J2260 (Section 7.8) | Fuel Exposure preconditioning |
| SAE J2260 (Chapter 7.9) | Methanol Resistance |
| SAE J2288 | Life Cycle Test of Electric Vehicle Modules |
| SAE J2334 | Copper Accelerated Acetic Acid Salt Spray (CASS) Test Cyclic Corrosion Test |
| SAE J2412 | Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Radiation Xenon-Arc Apparatus |
| SAE J2412- J2527- J1885 (Inactive) | Abrasion (Artificial) Artificial Weathering (Xenon Arc) |
| SAE J2412 | Indoor -Color Fastness -Xenon Arc |
| SAE J2464 | Passive Dissipation Resistance, Short Circuit, Overcharge, Overdischarge, Disconnector Shutdown Integrity |
| SAE J2501 | Round, Shielded and Unshielded, 60 V and 600 V Multicore Sheathed cables |
| SAE J2527 | Accelerated Exp |
| SAE J2544 | Plug-In Relay Test Methods |
| SAE J2635 | Filiform Corrosion |
| SAE J2863 | Automotive Trailer Towing Coupling |
| SAE J2962-1 | Communications Transceivers Qualification Requirements – LIN |
| SAE J2962-2 | Communications Transceivers Qualification Requirements – CAN |
| SAE J315 | Fiberboard Test Procedure |
| SAE J322 | Non-Metallic Trim Materials–Test Method for Determining Dyeing Resistance to Hydrogen Sulfide Gas |
| SAE J323 | Determination of Cold Cracking of Flexible Plastic Materials (Method A) |
| SAE J323 (Method A) | Cold Cracking |
| SAE J365 | Method for testing the scratch resistance of flooring materials |
| SAE J365- SAE J861 | Cracking |
| SAE J365- SAE J948 (Taber only) | Wear |
| SAE J369 | Flammability |
| SAE J400 | Chip Resistance of Surface Coatings |
| SAE J406 | Methods for Determining the Hardenability of Steels |
| SAE J417 | Hardness |
| SAE J423 | Methods of Measuring Depth of Case |
| SAE J560 | Primary and Auxiliary Seven-conductor Electrical Connector for Truck-Trailer Connector Cable |
| SAE J575 | Lighting Devices and Components for Use in Vehicles Smaller than 2032 mm |
| SAE J576 | Test Methods and Equipment for Lighting Devices Used in Vehicles with a Total Height of Less than 2032 mm Plastics for Use in Optical Components such as Lenses and Reflectors of Motor Vehicle Lighting Devices |
| SAE J578 | Color Specification |
| SAE J855 | Textile and Plastic Stretching and Set |
| SAE J860 | Measuring Mass (Weight) of Organic Trim Materials |
| SAE J861 | Color Transfer |
| SAE J882 | Measuring the Thickness of Automotive Textiles and Plastics |
| SAE J883 | Determination of Dimensional Stability of Automotive Textile Materials |
| SAE J911 | Surface Texture, Roughness (Ra), Peak Number (Pc) and Average Profile Spacing, (Rsm) Metallic Coated and Uncoated Steel Sheer/Strip Measurement to be Formed and/or Painted |
| SAE J912 | Determination of Blocking Resistance and Associated Properties of Automotive Trim Materials |
| SAE J913 | Roving Automotive Fabrics and Fibrous Materials |
| SAE J948 | Determining the Resistance of Automotive Bodycloth, Vinyl, and Leather to Abrasion and Attachment of Automotive Bodycloth |
| SAE J948- J1530- J1847 | Wear Resistance Taber |
| SAE J949 | Determination of Hardness of Interior Flooring Materials and Surfaces by Three-Point Bending Test |
| SAE J965 | Abrasion |
| SAE USCAR 15 | Specification for Testing Automotive Miniature Bulb Socket/Wingplate Assemblies |
| SAE USCAR 2 | Performance Specification for Automotive Electrical Connector Systems |
| SAE USCAR 20 -SAE /USCAR-2 | Field Associated Life Test Addendum |
| SAE USCAR 21 | Performance Specification for Wire-to-Terminal Electrical Crimps |
| SAE USCAR 24 | Helium Leak Detection |
| SAE USCAR 24 (Chapter 5.2.3.8) | Live Dissection |
| SAE USCAR 24 (Section 5.2.4.8.5) | Salt Mist-Salt Spray |
| SAE USCAR 24 (Section 5.2.4.8.6) | Drop Test |
| SAE USCAR 24, Sec. 5.2.3.4 | Electrical Resistance (1 milliohm to-megaohm) |
| SAE USCAR 3 | Standard for Testing Automotive Miniature Bulbs |
| SAE/USCAR-2 | High Voltage Connector Performance Supplement to SAE USCAR -37 |
| SAE USCAR-1 | Salt spray test and evaluation of fastener finishes |
| SAE USCAR-15 | Specification for Testing Automotive Miniature Bulb Socket/Circuit Plate Assemblies |
| SAE USCAR-15-3 | Specification for Testing Automotive Bulb Sockets |
| SAE USCAR-17-5 | Performance Specification for Automotive RF Connector Systems |
| SAE USCAR-2 | Automotive Electrical Connection Systems Standard |
| SAE USCAR-2 Rev. 6 | Performance specification for automotive electrical connector systems |
| SAE USCAR-21 | Rev. 3 |
| SAE USCAR-21-3 | Performance specification for wire-to-terminal electrical crimps |
| SAE USCAR-23-1 -Road vehicles | 60 V and 600 V solid wires – Dimensions, test methods and requirements |
| SAE USCAR-25-3 | Ergonomics Specification for Electrical Connections |
| SAE USCAR-2-6 | Performance Specification for Automotive Electrical Connector Systems |
| SAE/USCAR-2 | High Voltage Connector Performance Supplement to SAE USCAR-37 |
| SAE USCAR-38 | Performance Specification for Ultrasonically Welded Wire / Cable Termination |
| SAE USCAR-38-1 | Performance Specification for ultrasonically welded wire terminations |