ISO 标准能量块返回 Back

Organiser:


Registration:

By means of the attached form

Intention:

Confirmation of technical competence of participating laboratories

Data evaluation:

Based on ISO/IEC 17043 and ISO 13528. Usually the participation is approved

for accreditations according to NADCAP.

Confidentiality:

Each laboratory receives a specific code number

Documentation:

Certificate

Final report with a list of participants in alphabetical order with declaration of consent; determination of measurement uncertainty according to the current standards and guidelines.

 

No. 2001-HB

Hardness testing Brinell

Test standard:

ISO 6506, part 1, HBW 2,5/187,5

Material:

Reference hardness block

Test program:

five hardness measurements on reference hardness block

Test sequence:

Each participant receives a reference specimen.

Results to be submitted:

five hardness values of the hardness blocks

Assigned value:

Certified reference values of MPA NRW Dortmund, Germany

Additional information

provided by organiser:

Statement to measurement uncertainty

Participation fee:

estimated start: III. quarter 2020

 

No. 2001-HR

Hardness testing Rockwell C

Test standard:

ISO 6508, part 1, HRC

Material:

Reference hardness block

Test program:

3 x five hardness measurements on reference hardness blocks

Test sequence:

Each participant receives three reference specimens.

Results to be submitted:

3 x five hardness values of the hardness blocks

Assigned Value:

Certified reference values of MPA NRW Dortmund, Germany

Additional information

provided by organiser:

Statement to measurement uncertainty

Participation fee:

III. quarter 2020

 

 

No. 2001-HV

Hardness testing Vickers

Test standard:

ISO 6507, part 1, HV 1, HV 10/HV 30

Material:

Reference hardness block

Test program:

five hardness measurements on reference hardness block

Test sequence:

Each participant receives a reference specimen.

Results to be submitted:

five hardness values of the hardness blocks

Assigned value:

Certified reference values of MPA NRW Dortmund, Germany

Additional information

provided by organiser:

Statement to measurement uncertainty

Participation fee:

HV 1 or HV 10/HV 30:

HV 1 and HV 10/HV 30:

 

 

No. 2001-HT

Mobile hardness testing

Test Standard:

All mobile methods are accepted; Leeb (HLD), UCI, TIV

Material:

Reference specimens

Production of specimens:

By the organiser

Test sequence:

Each reference specimen will be tested by several participants.

There will be an arrangement of the dates in advance.

Results to be submitted:

5 hardness values according to the method used

Assigned value:

Reference value

Participation fee:

estimated start: III. quarter 2020


 

No. 2002

Testing of fasteners

Test standard:

ISO 898-1, ISO 3506-1

Material:

bolts

Production of specimens:

by the organiser

Results to be submitted:

according to standard, e.g. tensile test

Assigned Value:

Consensus value calculated from the results of all the participants

Participation fee:

estimated start: III. quarter 2020

 

 

No. 2003

Emission spectrometry steel

Test standard:

In-house procedure

Material:

Material similar to daily laboratory work (no „synthetic alloy“)

a) low alloyed steel

b) high alloyed steel

Results to be submitted:

Characteristic values according to specifications

Assigned value:

Consensus value calculated from the results of all participants

Additional information:

Statement to measurement uncertainty

Participation fee:

one alloy:

two alloys:

 

No. 2004

Emission spectrometry (non ferrous- metals)

Test standard:

In-house procedure

Material:

Material similar to daily laboratory work (no „synthetic alloy“)

Aluminium-alloy

Results to be submitted:

Characteristic values according to specifications

Assigned value:

Consensus value calculated from the results of all the participants

Additional information:

Statement to measurement uncertainty

Participation fee:


 

No. 2005

Resistance against intergranular attack

Test Standard:

ISO 3651, part 2

Material:

Stainless steel

Production of specimens:

by the organiser

Results to be submitted:

Acc. to standard

Assigned value:

Consensus value calculated from the results of all participants

Participation fee:


 

No. 2006

Indirect verification of salt spray test chamber

Test standard:

ISO 9227

Material:

Reference specimens

Production of specimens:

by the organiser

Results to be submitted:

Mass loss

Assigned value:

Reference value

Participation fee:


 


 

No. 2007-RAl

Tensile test aluminium (round specimens)

Test standard:

ISO 6892-1

Material:

6 round test specimens, aluminium, d0 = 6 mm, specimen head: ISO thread M10, and/or 6 material sections, diameter 16 mm, length 110 mm each

Production of specimens:

by the organiser / by the participants

Results to be submitted:

Characteristic values according to the test standard, additionally “Young's

Module” and the measurement uncertainty

Assigned Value:

Consensus values calculated from the results of the participants

Additional information:

Statement to the influence of specimen preparation, to measurement uncertainty

of the test method

Participation fee:

2007-RAlM: Machined specimens:

2007-RAlU: Unmachined specimens:

Machined AND unmachined specimens:

 

 

No. 2007-FAl

Tensile test aluminium (flat specimens)

Test standard:

ISO 6892-1

Material:

6 flat specimens, aluminium, geometry according to ISO 6892-1 (2017),annex B, table B1,a0 = 1-3 mm, b0 = 20 mm, and/or

6 material sections of about 32 x 280 mm² each

Production of specimens:

by the organiser / by the participants

Results to be submitted:

Characteristic values according to the test standard, additionally “Young's

Module” and the measurement uncertainty

Assigned Value:

Consensus values calculated from the results of the participants

Additional information:

Statement to the influence of specimen preparation, to measurement uncertainty of the test method

Participation fee:

2007-FAlM: Machined specimens:

2007-FAlU: Unmachined specimens:

Machined AND unmachined specimens:

 

 

No. 2008

Non-destructive testing

Test standard:

UT, VT

Material:

UT: Steel specimens, app. 200 x 100 mm² with defined flaws

VT: Steel specimens app. 200 x 200 x 10 mm³ with weld seam in the middle, with flaws defined for the test method

ET: Cylindrical steel specimen with flaws defined for the test method

Results to be submitted:

UT: Wall thickness, number and position of flaws

VT: Type / position / size of flaws

Assigned value:

UT: Wall thickness: direct measurement; number and position of flaws: true value

PT: Sample solution of Fraunhofer IZFP Saarbrücken, Germany

Test sequence:

Each sample will be tested by several participants.

There will be an arrangement of the dates in advance.

Participation fee:

One method:
Two methods:

 

 

No. 2009-R

Tensile test steel (round specimens)

Test standard:

ISO 6892-1

Material:

Standard samples: 6 round test specimens, steel, d0 = 10 mm, specimen head: ISO thread M16 as per standard,

Alternate samples: specimens with d0 = 6 mm, specimen head: ISO thread M10, and/or 6 material sections, 20 x 20 mm², length 150 mm each

Production of specimens:

by the organiser / by the participants

Results to be submitted:

Characteristic values according to the test standard, additionally “Young's Module” and the measurement uncertainty

Assigned Value:

Consensus values calculated from the results of the participants

Additional information:

Statement to the influence of specimen preparation, to measurement uncertainty

of the test method

Participation fee:

2009-RM: Machined specimens:

2009-RU: Unmachined specimens:

Machined AND unmachined specimens:



No. 2009-BST

Tensile test steel for the reinforcement

Test standard:

ISO 15630-1, ISO 6892-1

Material:

6 reinforcing bars, diameter: 12 mm, length: 1.000 mm

Production of specimens:

by the participants (if required)

Results to be submitted:

according to the test standard, additionally Young's Module and the measurement

uncertainty (not evaluated)

Assigned Value:

Consensus values calculated from the results of the participants

Additional information:

Measurement uncertainty of test procedure

Participation fee:


 

 

No. 2010F

Tensile test steel flat specimens, 1-3 mm

Test standard:

ISO 6892-1

Material:

6 flat specimens, steel, geometry according to ISO 6892-1 (2017), annex B, table B1, a0 = 1-3 mm, b0 = 20 mm, and/or

6 material sections of about 32 x 280 mm² each

Production of specimens:

by the organiser / by the participants

Results to be submitted:

Characteristic values according to the test standard, additionally “Young's

Module” and the measurement uncertainty

Assigned Value:

Consensus values calculated from the results of the participants

Additional information:

Statement to the influence of specimen preparation, to measurement uncertainty

of the test method

Participation fee:

2010FM: Machined specimens:

2010FU: Unmachined specimens:

Machined AND unmachined specimens:

 

 

No. 2011

Charpy impact test ready to test specimens

Test standard:

ISO 148-1 / ISO 148-2 (2 mm striker)

Material:

Charpy test specimens, impact energy low level (RT), average level (RT),

high level (RT), super high level (RT)

Production of specimens:

by the organiser

Results to be submitted:

5 values according to ISO 148 each energy level

Assigned value:

Consensus value, limits according to ISO 148-2

Additional information:

Measurement uncertainty according to ISO 148-2

Participation fee:

One energy level:

Two energy levels:

Three energy levels:

Four energy levels:


 

No. 2011

Charpy impact test unmachined specimens

Test standard:

ISO 148-1 / ISO 148-2 (2 mm striker)

Material:

Material sections, app. dimensions: 57 x 12 x 12 mm³, impact energy low level (RT), average level (RT), high level (RT), super high level (RT)

Production of specimens:

by the participants

Results to be submitted:

5 values according to ISO 148 each energy level

Assigned value:

Consensus value, limits according to ISO 148-2

Additional information:

Measurement uncertainty according to ISO 148-2

Participation fee:

One energy level:

Two energy levels:

Three energy levels:

Four energy levels:

 

No. 2013

Metallography, image analysis

Test standard:

e. g. ISO 643, ASTM E 112

appointment also possible via digital image processing

Material:

Micrograph; in part simulated, in digital form

Results to be submitted:

e.g. grain size steel / phase content steel / phase content aluminium

Assigned Value:

Consensus value, sample solution

Participation fee:


 

No. 2014

Metallography, sample preparation

Test standard:

e. g. ISO 643, ASTM E 112

Material:

Metallic samples for grinding preparation and analysis

Results to be submitted:

e.g. carbon content, grain size

Assigned Value:

Consensus value, sample solution

Participation fee:


 

 

No. 2015

Surface roughness

Test standard:

All applicable standards allowed

Material:

Reference specimens

Production of specimens:

by the organiser

Test procedure:

Each participant receives a reference specimen

Results to be submitted:

Ra, Rz, Rmax

Assigned Value:

Reference value

Participation fee: